| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
riscv: errata: select RISCV_ALTERNATIVE_EARLY for THEAD GHOSTWRITE
errata_probe_ghostwrite() only marks the CPU as vulnerable when it is
called at the RISCV_ALTERNATIVES_EARLY_BOOT stage, and the mitigation
in ghostwrite_enable_mitigation() only takes effect if the vulnerable
state was recorded before the boot alternatives are patched.
The early boot stage is only executed when CONFIG_RISCV_ALTERNATIVE_EARLY
is enabled, which currently is only selected by ERRATA_THEAD_MAE. In a
kernel built with ERRATA_THEAD_GHOSTWRITE=y but ERRATA_THEAD_MAE=n, the
early alternatives never run, so ghostwrite_state is never set to
VULNERABLE: ghostwrite_enable_mitigation() returns false, xtheadvector
remains enabled, and sysfs reports "Not affected" on a vulnerable
T-Head C9xx CPU.
Select RISCV_ALTERNATIVE_EARLY from ERRATA_THEAD_GHOSTWRITE so that the
vulnerability is detected in the early boot stage and the default
mitigation is applied. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: use the local P2P device on metadata allocation failure
nvmet_req_alloc_p2pmem_sgls() assigns req->p2p_dev only after the data
and metadata SGL allocations succeed. If the data allocation succeeds
but the metadata allocation fails, out_free_sg passes req->p2p_dev to
pci_p2pmem_free_sgl() before that assignment has taken place.
Pass the local p2p_dev argument instead, so cleanup uses the same PCI
device as the successful data allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: stop exchanging reflink flags when exchanging mappings
When an exchange covers both files from offset 0 to i_disk_size,
xmi_can_exchange_reflink_flags() assumes every mapping moved and hands
the reflink flag over to the other file.
That assumption is wrong. A file can still own shared blocks past
i_disk_size, e.g. after EXCHANGE_RANGE_TO_EOF sets a smaller size
without unmapping anything. The flag is cleared anyway, and the next
write to such a block happens in place instead of CoW, corrupting the
other file that shares it.
Commit a23eca88448e ("xfs: fix exchange-range reflink flag clearing
issue with INO1_WRITTEN") fixed one instance of this. Rather than add
another special case, stop moving the flags.
xfs_exchmaps_ensure_reflink() already sets the flag on both inodes
before the exchange, so both just keep it.
Nothing sets CLEAR_INO{1,2}_REFLINK anymore. Intents logged by older
kernels may still carry them; recovery already masks them off, so they
stay in the log format mask and are ignored.
XFS_IOC_SWAPEXT has the same problem: it moves the reflink flag from
one inode to the other along with the extents. Just removing that is
not enough here: the exchange path flags both inodes up front in
xfs_exchmaps_ensure_reflink(), but swapext has no such step, so the
inode receiving the shared extents would be left without the flag.
Set it on both inodes instead, and make sure both have a CoW fork,
since an inode with the reflink flag is expected to have one.
The flag now stays until FALLOC_FL_UNSHARE_RANGE, xfs_scrub, or a
truncate to zero removes it. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix xattr replace when multiple xattrs are packed in the same item
If we have a btrfs_dir_item item that packs multiple xattrs and then we
replace the value of one of them (with the setxattr(2) family of syscalls)
with another value of a different size, we end up not having a fully
initialized btrfs_dir_item, resulting in a corruption that the tree
checker will detect at extent buffer writeback time.
This is because in btrfs_setxattr() when we find a btrfs_dir_item with
multiple xattrs (due to the crc32c hash of their name being the same)
we delete one of the xattr items (btrfs_dir_item) and then insert a new
one, but the deletion and insertion results in shifting existing data in
the leaf and therefore when the new value of a xattr has a different size,
the new btrfs_dir_item is placed in a leaf section that was not
initialized and we only copy the value's data and set the value's length
in the new btrfs_dir_item, without setting the name, the name's length,
the key (which must be all zeroes for xattrs), flags (BTRFS_FT_XATTR) and
transaction ID.
The following script reproduces the issue:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
touch $MNT/testfile
# Add two xattrs that, on btrfs, have the same hash (crc32c) for their
# name and therefore are packed into the same btrfs_dir_item.
setfattr -n user.foobar -v 123 $MNT/testfile
setfattr -n user.WvG1c1Td -v qwerty $MNT/testfile
# Verify the xattrs are present.
echo "xattrs before:"
getfattr --absolute-names --dump $MNT/testfile
# Now replace the value of the foobar xattr with a significantly larger
# value.
setfattr -n user.foobar -v abcdefghijklmnopqrstuvwxyz $MNT/testfile
# Check the xattrs have the expected values.
echo "xattrs after:"
getfattr --absolute-names --dump $MNT/testfile
umount $MNT
Running it:
$ ./test.sh
(...)
xattrs before:
# file: /mnt/sdi/testfile
user.WvG1c1Td="qwerty"
user.foobar="123"
xattrs after:
# file: /mnt/sdi/testfile
user.WvG1c1Td="qwerty"
So the "user.foobar" xattr is missing and there was a transaction abort
when unmounting the fs with the following traces in dmesg:
$ dmesg
[869800.159271] BTRFS warning (device sdi): access to eb bytenr 30474240 len 16384 out of range start 16015 len 25964
[869800.159293] ------------[ cut here ]------------
[869800.159296] WARNING: fs/btrfs/extent_io.c:4408 at report_eb_range+0x44/0x60 [btrfs], CPU#8: getfattr/2605179
[869800.168961] Modules linked in: btrfs dm_thin_pool (...)
[869800.190527] CPU: 8 UID: 0 PID: 2605179 Comm: getfattr Tainted: G W 7.3.0-rc3-btrfs-next-244+ #1 PREEMPT(full)
[869800.193726] Tainted: [W]=WARN
[869800.194502] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[869800.197576] RIP: 0010:report_eb_range+0x44/0x60 [btrfs]
[869800.198985] Code: 48 8b 7b 18 (...)
[869800.203531] RSP: 0018:ffffce4541937d58 EFLAGS: 00010246
[869800.204609] RAX: 0000000000000000 RBX: ffff8dde054b8738 RCX: 0000000000000000
[869800.206137] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffc04c92a0
[869800.207645] RBP: 0000000000003e8f R08: 0000000000000000 R09: 3fffffffffefffff
[869800.226175] R10: ffffce4541937a88 R11: 0000000000000003 R12: 000000000000656c
[869800.227594] R13: ffff8dde14be800f R14: 000000000000656c R15: 0000000000000069
[869800.229097] FS: 00007f59023bb780(0000) GS:ffff8de5788ed000(0000) knlGS:0000000000000000
[869800.231137] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[869800.232321] CR2: 0000558dc45e6a78 CR3: 0000000765b16004 CR4: 0000000000370ef0
[869800.233783] Call Trace:
[869800.234330] <TASK>
[869800.234791] read_extent_buffer+0x4d/0x100 [btrfs]
[869800.235898] btrfs_listxattr+0x199/0x240 [btrfs]
[869800.236912] vfs_listxattr+0x51/0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: don't inherit MNT_UMOUNT in clone_mnt()
MNT_UMOUNT gets raised on a mount that umount_tree() or umount_one() has
taken out of its namespace. It's never cleared. __detach_mounts()
unhooks a mount that carries it instead of unmounting it.
disconnect_mount() lets an unmounted child stay attached only if its
parent carries it. propagate_umount() takes it as the sign that a mount
is going to be unmounted when it decides what else can be unmounted,
where a chain of locked mounts ends and where a for reparenting an
overmount.
clone_mnt() copies the flags of the source and only masks
MNT_INTERNAL_FLAGS which doesn't include MNT_UMOUNT. A mount that was
lazily unmounted but is kept alive by a file descriptor can still be
copied when its root is an nsfs or pidfs file because may_copy_tree()
accepts those before checking whether the source is mounted at all:
mount --bind /proc/self/ns/net /tmp/x
exec 3< /tmp/x
umount -l /tmp/x
mount --bind /proc/self/fd/3 /tmp/y
The mount on /tmp/y is attached to the caller's namespace with
MNT_UMOUNT already set and every copy of it inherits the flag again.
That causes a number of bugs:
- Unlink its mountpoint from a mount namespace where it isn't one.
__detach_mounts() takes it for a mount that was unmounted earlier,
unhooks it from its parent and drops the reference the namespace
holds on it. It stays in the namespace with one reference too few
and as its own parent, so it can't be unmounted through the file
descriptor anymore and the namespace never finds it again. When the
namespace goes away it's leaked and points to a freed struct
mnt_namespace that may_change_propagation() and anon_ns_root() read
on the next propagation change or mount_setattr() through the file
descriptor.
- Make it shared and unmount a peer. trace_transfers() follows the
flag from the peer into it and strips it from its peer group.
- Let a propagated umount reach it. gather_candidates() marks it with
T_UMOUNT_CANDIDATE but never puts it on the candidate list, so the
mark is never cleared and every later propagated umount skips it. If
it's the parent of a locked mount handle_locked() takes it as the
cutoff and commits the locked child that should have stayed and
disconnect_mount() leaves that child attached to it, unmounted under
a mounted parent, which is what disconnect_mount() exists to
prevent. When the namespace goes away umount_tree() visits the child
a second time. And once __detach_mounts() has made it its own parent
reparent() never finds the end of the chain of unmounted parents.
A clone is a new mount that has never been unmounted. Add MNT_UMOUNT
to MNT_INTERNAL_FLAGS so clone_mnt() never copies it. And warn when
umount_tree() reaches a mount that already has it set. |
| In the Linux kernel, the following vulnerability has been resolved:
optee: register TEE devices only once fully initialized
optee_probe() called tee_device_register() on both the client and the
supplicant device before the rest of struct optee had been initialized.
tee_device_register() calls cdev_device_add(), which does two things at
once: it creates /dev/tee0 and /dev/teepriv0, and it links the device
into the tee class so that class_find_device() can find it. From that
moment on the device is reachable both from user space via tee_open()
and from kernel space via tee_client_open_context(). The only gate in
teedev_open() is tee_device_get(), which merely checks that
teedev->desc is non-NULL, which was already set by tee_device_alloc().
Therefore, there is effectively no gate at all.
A context opened in that window can run against a struct optee where
- optee->call_queue.mutex is not initialized by optee_cq_init()
- optee->supp mutex and completions is not initialized by
optee_supp_init()
- optee->rpmb_dev_mutex is not initialized yet,
- the message argument cache is not initialized by
optee_shm_arg_cache_init()
- optee->ctx is still NULL
Any open session or invoke during this window takes uninitialized
mutexes and dereferences a NULL pointer.
Fix it by moving both tee_device_register() calls down to the point
where all of struct optee is set up.
[JW: adding fixes and cc] |
| In the Linux kernel, the following vulnerability has been resolved:
Input: ati_remote2 - fix type confusion in device attribute handlers
Previously, the channel_mask and mode_mask attributes were registered on
the parent usb_device via sysfs_create_group(). When commit b20d6bf8014b
("Input: ati-remote2 - use driver core to instantiate device
attributes") converted the driver to let the driver core manage them via
dev_groups in struct usb_driver, the attributes moved to the bound
usb_interface devices, but the show and store callbacks were not updated
accordingly.
As a result, the callbacks still invoked to_usb_device() on a device
pointer belonging to a struct usb_interface, producing an invalid
usb_device pointer.
Use to_usb_interface() directly in the attribute handlers to obtain the
interface and its driver data. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: of: fill in supply names in of_regulator_bulk_get_all()
of_regulator_bulk_get_all() returns an array it allocated itself, and
fills in only the consumer of each entry. Every other way of getting a
bulk array has the supply name set, because the caller provides it, and
the core expects it to be there: regulator_bulk_enable() prints it when
a supply fails to enable, so a caller that hands such an array to it
dereferences uninitialised memory on that path.
Copy each name into the array's own allocation, right behind the
entries, so that it shares the array's lifetime and callers still have
nothing extra to free. That also retires the fixed 64 byte stack buffer
the names were assembled in, which is_supply_name() never bounded the
copy against. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: exar: initialize the ID before registering its cleanup
devm_add_action_or_reset() invokes the cleanup action immediately when
registering the action fails. gpio_exar_probe() currently stores the
allocated ID in exar_gpio only after registering the action, so that
failure makes exar_devm_ida_free() release ID 0. If the allocated ID is
nonzero, this leaks that ID and can free ID 0 belonging to another device.
Store the ID before registering the cleanup action so both the immediate
failure path and normal device teardown release the correct allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
macsec: initialize SecY before registering the netdevice
Creating a MACsec device with MAC offload over an LRO-capable lower
device triggers a warning in rtmsg_ifinfo_build_skb() when IPv4
forwarding is enabled by default.
register_netdevice() invokes inetdev_init(), which disables LRO and emits
a NETDEV_FEAT_CHANGE notification. This reaches macsec_fill_info() before
macsec_add_dev() initializes the SecY. key_len is still zero, so
macsec_fill_info() returns -EMSGSIZE and trips the WARN_ON in
rtmsg_ifinfo_build_skb(), even though the skb has enough space.
Even without the warning, notifications during registration can report
uninitialized SecY attributes, including the SCI. This ordering has existed
since the driver was introduced.
Initialize the SecY and apply the new-link attributes before registration.
Move MAC address inheritance into macsec_newlink() so the SCI can also be
initialized before registration-time notifications report it. Move the
per-CPU statistics and metadata destination allocation into ndo_init(),
and release partial allocations on failure. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/vc4: Disable the V3D interrupt across runtime suspend
vc4_irq_disable() masks the V3D interrupt sources and then calls
synchronize_irq() before the V3D is powered down. However, by itself,
this is not enough to quiesce the interrupt handler.
synchronize_irq() waits for handlers that have already set
IRQD_IRQ_INPROGRESS, and for irqchips reporting IRQCHIP_STATE_ACTIVE.
A GIC interrupt chip is able to mark an interrupt active as soon as a
CPU acknowledges it, so there these checks cover the whole dispatch path.
On RPi 0-3, however, the interrupt controller is ARMCTRL, which has no
active state. A CPU that has read the hwirq out of the pending register
but has not yet reached handle_level_irq() stays invisible to
synchronize_irq().
During a power transition, vc4_irq() may therefore run after the power
domain is off, where every V3D register read will return 0xdeadbeef.
0xdeadbeef has FLDONE, FRDONE and OUTOMEM set. This problem doesn't
trigger NULL pointer dereference issues only because the functions
vc4_irq_finish_bin_job() and vc4_irq_finish_render_job() return early
when there is no job pointer, but OUTOMEM is still able to schedule
vc4_overflow_mem_work() after vc4_irq_disable() has already cancelled it.
Therefore, fix the spurious interrupts by disabling the interrupt line
across the PM transition. To preserve the enable/disable balance, move
vc4_irq_install() and request the IRQ line disabled before the first
runtime resume. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm/si: Don't schedule thermal work when queue isn't initialized
When DPM is turned off with the amdgpu.dpm=0 module parameter,
the thermal work queue isn't initialized so we shouldn't
schedule any work on it.
(cherry picked from commit bd018d36171a695952c6d391471c279c9e05c8b2) |
| In the Linux kernel, the following vulnerability has been resolved:
net: lan966x: restore RX state on reload failure
lan966x_fdma_reload() backs up rx->page_pool and rx->fdma before
reallocating the RX resources for the new MTU. If the allocation fails,
the restore path puts these fields back before restarting RX.
However, the reload path also updates rx->page_order and rx->max_mtu
before calling lan966x_fdma_rx_alloc(). These fields are not restored on
failure, so RX can be restarted with the old pages, old FDMA state and
old page pool, but with the page geometry from the failed new MTU.
This can make the XDP path advertise a frame size derived from the new
page_order while the actual RX pages still come from the old allocation.
For example, after a failed reload to a jumbo MTU, xdp_init_buff() may be
called with a frame size larger than the restored RX pages.
lan966x_fdma_rx_alloc_page_pool() also registers the newly allocated page
pool with each port's XDP RXQ before fdma_alloc_coherent() is called. If
fdma_alloc_coherent() fails, the new page pool is destroyed, but the
rollback path does not restore the per-port XDP RXQ mem model
registration either.
Save and restore rx->page_order and rx->max_mtu, and restore the old page
pool registration for each port's XDP RXQ before RX is started again.
This keeps the restored RX state consistent after a failed reload. |
| In the Linux kernel, the following vulnerability has been resolved:
cgroup/cpuset: Don't access cpuset_cgrp_subsys.root in is_in_v2_mode()
After seeing the patch [1] to guard is_in_v2_mode() with RCU, it makes
me realize that is_in_v2_mode() may be called in a context where a new
cgroup filesystem is being rebound with stale cpuset_cgrp_subsys.root
pointer. Avoid this potential UaF situation by adding a new cpuset_v2_mode
flag which is set when the cpuset_v2_mode mount option is used. This
flag is written into only when cpuset_bind() is being called with a
stable cpuset_cgrp_subsys.root value. The is_in_v2_mode() helper is
modified to read the new cpuset_v2_mode flag instead of accessing
cpuset_cgrp_subsys.root directly.
[1] https://lore.kernel.org/lkml/20260929084124.626693-2-arighi@nvidia.com |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: reset ar->num_stations on hardware start
When (multiple) hw restart occurs, we end up in a situation where we
cannot accept new stations / mesh peers. This seems to be the
'num_stations' in 'struct ath11k' that did not get reset properly in
this case. In ath11k_mac_op_start(), it was indeed the only accounting var
that did not get reset so let's clear it too.
This avoids problems like those:
[1248828.088023] WARNING: CPU: 0 PID: 12281 at net/mac80211/util.c:1682 ieee80211_reconfig_stations+0x98/0xc0
[1248828.088115] Call trace:
[1248828.088116] ieee80211_reconfig_stations+0x98/0xc0 (P)
[1248828.088119] ieee80211_reconfig+0x774/0x1438
[1248828.088123] ieee80211_restart_work+0x10c/0x178
[1248828.088127] process_one_work+0x178/0x3c0
[1248828.088130] worker_thread+0x280/0x440
[1248828.088133] kthread+0xe0/0xf8
[1248828.088137] ret_from_fork+0x10/0x20
[1248828.088141] ---[ end trace 0000000000000000 ]---
[1248836.686604] ath11k_pci 0000:04:00.0: refusing to associate station: too many connected already (128)
[1248836.686609] ath11k_pci 0000:04:00.0: Failed to add station: xx:xx:xx:xx:xx:xx for VDEV: 1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix self-redirect copied_seq double-counting
When a BPF stream_verdict program redirects an skb back to the same
socket (self-redirect with BPF_F_INGRESS), sk_psock_verdict_apply()
calls tcp_eat_skb() which advances tcp_sk->copied_seq. However, the
skb is then delivered to the socket's psock ingress queue and later
read by tcp_bpf_recvmsg_parser(), which also advances copied_seq via
the copied_from_self accounting path. This double-counting causes
copied_seq to advance by 2x the actual data length, triggering:
TCP recvmsg seq # bug 2: copied BF2E806, seq BF2E7FD, \
rcvnxt BF2E806, fl 0
WARNING: net/ipv4/tcp.c:2745 at tcp_recvmsg_locked+0x72b/0x2640
Call Trace:
tcp_recvmsg+0x10a/0x500
sock_recvmsg+0x168/0x1d0
__sys_recvfrom+0x19a/0x2a0
__x64_sys_recvfrom+0xe4/0x1f0
do_syscall_64+0xf7/0x530
entry_SYSCALL_64_after_hwframe+0x77/0x7f
cleanup rbuf bug: copied BF2E806 seq BF2E806 rcvnxt BF2E806
WARNING: net/ipv4/tcp.c:1609 at tcp_cleanup_rbuf+0xf2/0x1c0
Call Trace:
tcp_recvmsg_locked+0x8d1/0x2640
tcp_recvmsg+0x10a/0x500
sock_recvmsg+0x168/0x1d0
__sys_recvfrom+0x19a/0x2a0
__x64_sys_recvfrom+0xe4/0x1f0
do_syscall_64+0xf7/0x530
entry_SYSCALL_64_after_hwframe+0x77/0x7f
Fix this by converting self-redirect verdict to __SK_PASS at the
beginning of sk_psock_verdict_apply(). This bypasses the
__SK_REDIRECT case entirely (which calls sk_psock_eat_skb), letting
the __SK_PASS path queue the skb to the psock ingress queue. The
data is then read via tcp_bpf_recvmsg_parser(), which advances
copied_seq exactly once through copied_from_self. Cross-socket
redirects continue through __SK_REDIRECT with sk_psock_eat_skb()
unchanged. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix IRQ injection with SIGP Stop and Store Status
When __inject_sigp_stop() is called for a Stop and Store Status
operation, if the vCPU is running, the interrupt is marked as pending
and the status is stored by the thread performing the KVM_RUN IOCTL.
If the vCPU is already stopped, the status is stored immediately.
Storing the status means writing into userspace, which might fault, and
__inject_sigp_stop() is called from do_inject_vcpu() which in turn is
always called holding a spinlock, which is obviously an issue.
Fix this by returning -EWOULDBLOCK from __inject_sigp_stop(), and
adding a bool flag to indicate whether a store status is needed. The
callers of do_inject_vcpu() are modified to pass the pointer to the
bool flag; whenever a Store Status operation is needed, the callers can
now perform it outside the spinlock.
Opportunistically refactor kvm_s390_set_irq_state() to use
scoped_guard() and __free().
[ Added Fixes tag while picking -- Claudio ] |
| In the Linux kernel, the following vulnerability has been resolved:
x86/mm: Drop unnecessary PMD page copy when freeing
On a box with a discrete GPU, lockdep reports a possible deadlock as
soon as kswapd shrinks the TTM page pool. The immediate cause is an
x86 commit that added an mmap_read_lock() to kernel page protection
munging code.
The huge vmap code holds the same lock over a GFP_KERNEL allocation,
which is a no-no now that reclaim can take it. That allocation is in a
page table *free* path and ends up being for dubious purposes[1].
Basically, it tries to avoid hardware setting Accessed=1 in page table
entries that are unreachable by the hardware, a non-issue.
Remove the PMD copy. Detach the original PMD page at the PUD, flush
the mid-level caches, and free the PTE tables straight from the
detached PMD page. With no allocation left, the locking issue is gone.
Lockdep splat/analysis:
WARNING: possible circular locking dependency detected
7.3.0-rc3-f6e7b42bf05b+ #183 Tainted: G U
------------------------------------------------------
kswapd0/269 is trying to acquire lock:
((init_mm).mmap_lock){++++}-{4:4}, at: change_page_attr_set_clr+0x29a/0x4a0
but task is already holding lock:
(pool_shrink_rwsem){.+.+}-{4:4}, at: ttm_pool_shrink+0xb2/0x330 [ttm]
Chain exists of:
(init_mm).mmap_lock --> fs_reclaim --> pool_shrink_rwsem
The cycle is built from three edges:
1) pool_shrink_rwsem -> (init_mm).mmap_lock
The TTM shrinker restores the caching attribute of every page it
frees, while holding pool_shrink_rwsem:
ttm_pool_shrink()
-> ttm_pool_dispose_list()
-> ttm_pool_free_page()
-> set_pages_wb()
-> change_page_attr_set_clr() [ init_mm mmap read lock ]
2) fs_reclaim -> pool_shrink_rwsem
The same shrinker, called from reclaim.
3) (init_mm).mmap_lock -> fs_reclaim
ioremap() installing a huge PUD mapping over an existing PMD table:
ioremap_page_range()
-> vmap_range_noflush()
-> vmap_try_huge_pud() [ init_mm mmap read lock ]
-> pud_free_pmd_page()
-> __get_free_page(GFP_KERNEL) [ enters reclaim ]
[ dhansen: Lots of changelog munging/trimming and merged comments from my
version of the fix. ] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix lease break and ack state handling
Do not skip valid lease states containing WRITE_CACHING when breaking
level-II/read leases for writes and truncates.
Handle lease break acknowledgments according to the SMB2 rule that the
acknowledged state must be a subset of the server's break target. Apply
the acknowledged state directly and keep the break pending on failed ACKs. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: kprobes: Allow reentering kprobes while single-stepping
A kprobe can be hit while another kprobe is in KPROBE_HIT_SS state. This
can happen when tracing or perf code runs from the debug exception path
while the first kprobe is preparing or executing its out-of-line
single-step instruction.
Currently arm64 treats a kprobe hit in KPROBE_HIT_SS as unrecoverable,
the same as a hit in KPROBE_REENTER. This is too strict. A hit in
KPROBE_HIT_SS is still a one-level reentry and can be handled by saving
the current kprobe state and setting up single-step for the new probe,
just like reentry from KPROBE_HIT_ACTIVE or KPROBE_HIT_SSDONE.
The truly unrecoverable case is hitting another kprobe while already in
KPROBE_REENTER, because the reentry save area has already been consumed.
Move KPROBE_HIT_SS to the recoverable reentry cases and leave
KPROBE_REENTER as the unrecoverable nested reentry case.
This change also requires saving saved_irqflag in struct prev_kprobe.
When a nested kprobe calls kprobes_save_local_irqflag(), it overwrites
kcb->saved_irqflag with the currently masked DAIF value, losing the
outer kprobe's original DAIF state. Without this fix, when the outer
kprobe's single-step finishes, kprobes_restore_local_irqflag() applies
the wrong DAIF mask and leaves interrupts permanently disabled.
Extend struct prev_kprobe with a saved_irqflag field and save/restore it
alongside kp and status. This ensures the outer kprobe's original
interrupt state is preserved across reentry.
This mirrors the x86 fix in commit 6a5022a56ac3
("kprobes/x86: Allow to handle reentered kprobe on single-stepping"). |
