| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero dport diagnostics buffer to avoid info leak
qla2x00_do_dport_diagnostics() allocates the qla_dport_diag response
buffer with kmalloc_obj() (non-zeroing) and, on success, copies the full
sizeof(*dd) back to user space via sg_copy_from_buffer(). The inbound
sg_copy_to_buffer() only fills as many bytes as the user request payload
provides, and qla26xx_dport_diagnostics() zeroes only dd->buf. The
options and unused[] fields are therefore copied out uninitialized,
leaking kernel heap contents to user space.
Allocate with kzalloc_obj(), matching qla2x00_do_dport_diagnostics_v2(). |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Bound image count in qla2x00_update_fru_versions()
qla2x00_update_fru_versions() copies the user-supplied BSG request into
a fixed 256-byte stack buffer (bsg[DMA_POOL_SIZE]) and then iterates
list->count times over the qla_image_version array embedded in that
buffer, advancing the image pointer each iteration. count is taken
directly from user input with no upper bound, while only (DMA_POOL_SIZE
- sizeof(list->count)) / sizeof(struct qla_image_version) = 6 entries
actually fit. A larger count walks the image pointer off the end of the
stack buffer, reading adjacent kernel stack memory and sending it to the
device via qla2x00_write_sfp().
Reject requests whose declared count does not fit in the buffer. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Serialize flash version read in reset handler
The "update cache versions without reset" sysfs reset operation (0x20261)
calls get_flash_version(), which reads hardware flash registers, without
holding ha->optrom_mutex. The VPD update path serializes the same call
under optrom_mutex, so this reset path can interleave its flash register
accesses with a concurrent VPD or optrom flash operation and corrupt the
reads.
Hold ha->optrom_mutex across the get_flash_version() call to match the
VPD update path. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix FCE trace use-after-free during firmware dump
qla2x00_free_fce_trace() freed and cleared ha->fce while holding only
fce_mutex. The firmware-dump consumers qla27xx_fwdt_entry_t264() and
qla25xx_copy_fce() read ha->fce (NULL check followed by a copy of the
buffer) under hardware_lock and never take fce_mutex. A debugfs FCE
disable could therefore free the DMA buffer between a dump's NULL check
and its copy, resulting in a use-after-free.
Unpublish ha->fce under hardware_lock, then release the lock and free
the DMA buffer (dma_free_coherent() may sleep). A concurrent dump either
completes its check and copy with the buffer still valid, or observes
ha->fce == NULL and skips it. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero mailbox struct in qla2x00_get_firmware_state()
The mbx_cmd_t is allocated on the stack but left uninitialized.
qla2x00_mailbox_command() has several early-return paths (PCI permanent
failure, device failed, EEH busy, ISP abort pending, mailbox access
timeout, purge mbox) that return without writing the input mailbox
registers back into mcp->mb[]. qla2x00_get_firmware_state() then
unconditionally copies mcp->mb[1..6] (and mb[12]) into the caller's
states[] array regardless of the return value.
On such a failure the copied values are uninitialized kernel stack
memory, which is then exposed to userspace via the fw_state and
mpi_fw_state sysfs handlers. Zero the mailbox struct so a failed query
yields deterministic zeroed state instead of leaking stack contents. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix FCE trace enable parsing in debugfs
qla2x00_dfs_fce_write() called kstrtoul() with a NULL result pointer,
so a successful parse would dereference NULL and oops. Worse, the int
return value (0 on success, negative errno on failure) was assigned to
the unsigned long enable flag, inverting the intended logic: a valid
number was treated as "disable" while a parse failure enabled FCE.
Parse the value into enable and propagate parse errors to userspace. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Don't query firmware state while chip is down
qla2x00_fw_state_show() initializes rval to QLA_FUNCTION_FAILED and jumps
to the out: label when the chip is down or EEH is busy. The out: block
then re-issued qla2x00_get_firmware_state() because rval != QLA_SUCCESS,
defeating the chip-down/EEH-busy guards and issuing a mailbox command
(outside optrom_mutex) during ISP reset or PCI error recovery, which can
hang the adapter. It also turned a normal in-lock mailbox failure into a
second unsynchronized mailbox attempt.
Make the out: fallback only mark the firmware state as unknown. The
mailbox is now issued at most once, inside optrom_mutex, and only when
the chip is up and not EEH-busy. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Avoid req_q_map double-read in qla2x00_error_entry()
qla2x00_error_entry() reads ha->req_q_map[que] twice: once for the NULL
check and again when assigning it to req. The map slot is cleared by
qla25xx_free_req_que() (ha->req_q_map[que_id] = NULL under mq_lock)
during queue teardown, while the response-queue interrupt that drives
qla2x00_error_entry() is still registered (the IRQ is released later in
qla25xx_free_rsp_que()). If the slot is set to NULL between the two
reads, req becomes NULL and is dereferenced.
Read the slot once into req and NULL-check the local before use. mq_lock
is a mutex and cannot be taken from interrupt context, so the single
read plus local check is the appropriate fix for the reported NULL
dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero-init bsg stack buffers to avoid info leak
Several bsg handlers stage their request/reply in an uninitialized 256-byte
on-stack buffer (uint8_t bsg[DMA_POOL_SIZE]) and fill it via
sg_copy_to_buffer(), which only copies as many bytes as the user-supplied
request payload. When the request is shorter than the structure, the
remainder of the buffer is left holding stale stack data.
qla2x00_read_fru_status() and qla2x00_read_i2c() then copy the full
structure back to the reply payload with sg_copy_from_buffer(), leaking the
uninitialized stack bytes to user space. The write/update paths do not copy
the buffer back, but can feed uninitialized fields to the device.
Zero the stack buffer at declaration in all five handlers, mirroring the
heap kzalloc() approach, so short requests can no longer expose stale
memory. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Skip NVMe LS reject IOCB when FW not started
qla_nvme_xmt_ls_rsp() bails out to the out: label when firmware is not
started (!ha->flags.fw_started), but the out: path unconditionally calls
qla_nvme_ls_reject_iocb(), which ends in qla2x00_start_iocbs() and an
unconditional doorbell write to the request queue in-pointer register.
This rings the firmware doorbell and queues an IOCB that stopped or
resetting firmware cannot consume, and touches MMIO during the reset/EEH
window where fw_started is also clear.
Only emit the LS reject IOCB (and ring the doorbell) when fw_started is
set; otherwise just clean up and return. The post-allocation failure
cases (SRB alloc / qla2x00_start_sp() failure) run with firmware started
and still send the reject. Apply the same guard to the reject emission
in qla2xxx_process_purls_pkt(). |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: use the mount idmap for the owner check in f2fs_xattr_advise_set()
f2fs_xattr_advise_set() calls inode_owner_or_capable() with &nop_mnt_idmap
before allowing the "system.advise" xattr to be set, instead of the idmap
that the VFS passes to the ->set() handler.
f2fs supports idmapped mounts, so on such a mount this checks the caller's
fsuid against the unmapped on-disk owner rather than the mapped owner: the
actual owner can be wrongly denied with -EPERM and an unrelated caller
wrongly allowed. Pass the handler's idmap instead. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix dentry folio leak in find_in_level
find_in_level() gets a dentry folio with f2fs_find_data_folio() before
calling find_in_block(). If find_in_block() returns an error, the
function stores the error in res_folio and breaks out of the loop without
dropping the dentry folio.
This leaks the folio reference on the find_in_block() error path. Drop
the dentry folio before returning the error to the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: avoid NULL checkpoint thread access in sysfs
checkpoint_merge can be enabled even when no checkpoint merge thread is
running. A read-only mount is one case: f2fs does not start
f2fs_issue_ckpt there, but ckpt_thread_ioprio is still writable through
sysfs.
The ckpt_thread_ioprio store path updates the saved ioprio value and,
when checkpoint_merge is enabled, calls set_task_ioprio() for the
checkpoint thread. If cprc->f2fs_issue_ckpt is NULL, that dereferences a
NULL task pointer.
Protect ckpt_thread_ioprio sysfs writes with s_umount as well, so the
checkpoint thread cannot disappear under the store path while updating
its ioprio. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to migrate all curseg types during free_segment_range
In free_segment_range(), the curseg evacuation loop only iterates up to
NR_CURSEG_PERSIST_TYPE (0..5), missing non-persistent in-memory curseg
types such as CURSEG_COLD_DATA_PINNED and CURSEG_ALL_DATA_ATGC.
Even though these in-memory curseg types are not saved in the on-disk
checkpoint header, they still occupy active physical segments at runtime.
If an active in-memory curseg happens to be allocated within the segment
range being truncated during filesystem shrink, failing to evacuate it
will cause subsequent writes to the curseg attempting out-of-bounds I/O
on the truncated storage range.
Fix this by expanding the curseg evacuation loop upper bound to
NR_CURSEG_TYPE to ensure all active curseg types are safely migrated
out of the target range. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix to avoid potential deadloop in f2fs_fsync_node_pages()
There is potential deadloop in race condition:
Thread A Thread B
- fsync
- f2fs_do_sync_file
- f2fs_fsync_node_pages
- last_fsync_dnode
- folio_get(last_folio)
- f2fs_setattr
- f2fs_truncate
- f2fs_truncate_blocks
- f2fs_do_truncate_blocks
- f2fs_truncate_inode_blocks
- truncate_dnode
- truncate_node
- invalidate_mapping_pages
- folio->mapping = NULL
- is_node_folio alwasy return false
- atomic && !marked is always true,
then goto retry |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: protect critical_task_priority updates with s_umount
The sysfs store path already takes s_umount for GC thread control
entries, and ckpt_thread_ioprio is covered as well.
critical_task_priority also updates checkpoint or GC kthread scheduling
state, but it is not covered by that serialization. It can race with
remount or teardown paths that are stopping those threads.
Protect critical_task_priority sysfs writes with s_umount too. |
| In the Linux kernel, the following vulnerability has been resolved:
f2fs: fix valid block count leak on data block allocation failure
In __allocate_data_block(), when allocating a new data block
(dn->data_blkaddr == NULL_ADDR), inc_valid_block_count() is
called first to increment total_valid_block_count and i_blocks.
If the subsequent f2fs_allocate_data_block() fails, the function
returns the error directly without rolling back the
already-incremented block counts, causing a permanent leak.
Fix this by calling dec_valid_block_count() to undo the
increment before returning the error. The condition
old_blkaddr == NULL_ADDR precisely identifies the case where
inc_valid_block_count() was called. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Fix init ordering in amdgpu_vram_mgr_init()
drmm_cgroup_register_region() is called before INIT_LIST_HEAD() and
gpu_buddy_init() in amdgpu_vram_mgr_init(). If it fails, the function
returns early and bypasses those initializations.
Since adev->mman.initialized is set to true before amdgpu_vram_mgr_init()
is called, a failure triggers amdgpu_ttm_fini(), which calls
amdgpu_vram_mgr_fini(), which then:
- Calls list_for_each_entry_safe() on reservations_pending and
reserved_pages, whose list_head::next pointers are zero-initialized
(NULL). The loop does not recognize them as empty and dereferences NULL.
- Calls gpu_buddy_fini(), which iterates free_trees[] unconditionally
via for_each_free_tree(). Since mm->free_trees is NULL
(never allocated), this dereferences NULL.
Both result in a kernel panic on the module load error path.
Fix by moving drmm_cgroup_register_region() to after the list and buddy
allocator are fully initialized, so the teardown path is safe to run. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: avoid force-completing uninitialized UVD rings
uvd_v7_0_sw_init() does not initialize the UVD decode ring for an
SR-IOV VF. However, amdgpu_uvd_resume() unconditionally force-completes
the decode ring when restoring its fence sequence.
Skip fence completion when the fence driver is not initialized. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panel-edp: fix i2c adapter leak on probe failure
Make sure to drop the i2c adapter reference on probe failure (e.g.
probe deferral) and on driver unbind also if a devicetree redundantly
uses the 'ddc-i2c-bus' property to point to the aux ddc bus. |
