| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: cs35l34: drain threaded IRQ before runtime suspend
cs35l34_runtime_suspend() currently switches the codec into
regcache_cache_only(true), asserts reset low, and powers the device off
without first quiescing the threaded IRQ registered by
devm_request_threaded_irq(). That leaves a window where
cs35l34_irq_thread() can still run after suspend has removed live
hardware access.
A running system can reach this during runtime PM while the driver still
has critical fault IRQs unmasked. If the threaded handler runs in that
window, it reads volatile INT_STATUS_1..4 after cache_only has been
enabled, ignores the regmap_read() failures, and can still execute the
PROT_RELEASE_CTL release sequence or the BST fault power-down writes.
Use disable_irq() before entering cache_only/reset-low/power-off so any
in-flight threaded handler is drained and no new IRQ thread can run
while the device is suspended. Re-enable the IRQ only after
runtime_resume() has restored live register access with regcache_sync().
Since probe only logs request_threaded_irq() failures and keeps going,
track whether the IRQ was actually installed before disabling or
re-enabling it. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: hdac_hda: Fix hlink refcount leak on component registration failure
hdac_hda_dev_probe() gets the HDA link with snd_hdac_ext_bus_link_get()
before registering the ASoC component. If component registration fails,
the function returns without dropping the link reference.
Always call snd_hdac_ext_bus_link_put() after the registration attempt so
the reference taken during probe is balanced on both success and failure. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: atlas-sensor: fix PM reference leak in buffer postenable
atlas_buffer_postenable() acquires a runtime PM reference with
pm_runtime_resume_and_get() but returns the result of
atlas_set_interrupt() directly. If atlas_set_interrupt() fails,
the runtime PM reference is leaked and the device can never
autosuspend.
Add pm_runtime_put_autosuspend() on the error path to balance
the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: chemical: sgp30: Handle IAQ thread creation failure
kthread_run() can fail and return an error pointer, but sgp_probe() stores
it and returns success, so the device is registered without its IAQ thread
and sgp_remove() later passes the error pointer to kthread_stop(). Return
the error from probe instead. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: dac: m62332: Fix regulator reference count imbalance
m62332_set_value() enables the Vcc regulator on every write of a
non-zero value and disables it on every write of zero, without tracking
the channel's current state. Because the regulator is reference counted,
changing a channel directly from one non-zero value to another enables
it more than once, while a later write of zero disables it only once.
The reference count never returns to zero and the regulator is left
enabled indefinitely.
Only enable the regulator on the transition from zero to non-zero, and
only disable it on the transition from non-zero to zero, using the
previously stored channel value to detect the edge. Balance the
regulator on the I2C error path so the reference count stays consistent
if the write fails. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: apds9306: fix PM reference leak in apds9306_read_data()
apds9306_read_data() calls pm_runtime_resume_and_get() but several
error paths return directly without calling pm_runtime_put_autosuspend(),
leaking the runtime PM reference and preventing the device from
autosuspending.
Use PM_RUNTIME_ACQUIRE_AUTOSUSPEND() and PM_RUNTIME_ACQUIRE_ERR() to
automatically handle runtime PM reference release on all return paths. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: light: ltrf216a: fix runtime PM reference leak in error path
ltrf216a_get_lux() acquires a runtime PM reference by calling
ltrf216a_set_power_state(data, true). However, if
ltrf216a_read_data() fails, the function returns immediately without
dropping the reference.
This leaves the runtime PM usage count unbalanced, preventing the device
from autosuspending after a failed read.
Fix this by releasing the runtime PM reference before returning from the
error path. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: pressure: dps310: fix NULL pointer dereference on ACPI probe
When the device is enumerated through its ACPI HID (IFX3100),
i2c_client_get_device_id() returns NULL: the ACPI-derived client name
does not match the driver's i2c_device_id table. dps310_probe() then
dereferences that NULL pointer in "iio->name = id->name" and crashes the
kernel during probe.
The IIO device name is always "dps310", so set it directly and drop the
now-unused device-id lookup. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: nVMX: Ensure KVM_REQ_GET_NESTED_STATE_PAGES is cleared on VM-Exit
Always check and clear KVM_REQ_GET_NESTED_STATE_PAGES when emulating a
nested VM-Exit to ensure the request is cleared, even when KVM was built
with CONFIG_KVM_HYPERV=n, as KVM subtly relies on the "check" to clear
the flag and thus avoid double-mapping the vmcs12 pages, e.g. if KVM
manages to bail from VM-Enter without processing the request, and then
emulates VMLAUNCH or VMRESUME. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix length check __import_wp_info()
struct kvm_hw_breakpoint::len is a __u64 that is fully controlled by user
space. This is then assigned to wp_info->len, which is an int. The bounds
check is done on the truncated value while the allocation uses the
untruncated one:
wp_info->len = bp_data->len;
[...]
if (wp_info->len < 0 || wp_info->len > MAX_WP_SIZE)
return -EINVAL;
wp_info->old_data = kmalloc(bp_data->len, GFP_KERNEL_ACCOUNT);
Use the validated value for the allocation as intended. Without this
fix userspace can trigger >4GB allocations which will fail and result
in a WARN due to MAX_PAGE_ORDER. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix memory leak in guest debug handling
bp_data is freed only for the error case by kfree(bp_data).
Every successful KVM_SET_GUEST_DEBUG will leak bp_data. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Fix old_data leak in guest debug error path
__import_wp_info() allocates a per-watchpoint old_data buffer to back up
the original guest memory contents. If a later watchpoint of the same
KVM_SET_GUEST_DEBUG request fails to import, kvm_s390_import_bp_data()
jumps to the error label, which frees the wp_info array but not the
old_data buffers of the entries that were imported successfully. Up to
MAX_BP_COUNT - 1 buffers of up to MAX_WP_SIZE bytes are leaked per failed
request, and the request can be repeated.
Create error handling for cleaning up all created old_data memory
areas. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Free guest debug data on vcpu destroy
kvm_s390_clear_bp_data() is only called from
kvm_arch_vcpu_ioctl_set_guest_debug(), i.e. when user space changes or
disables debugging. A vCPU that is destroyed while hardware breakpoints
are still armed - the normal case when the VMM just exits or crashes -
leaks hw_bp_info, hw_wp_info and all old_data buffers, since generic KVM
frees the vCPU right after kvm_arch_vcpu_destroy().
That is bounded by MAX_BP_COUNT entries, so roughly 8 KiB per vCPU, but
it is unbounded over VM lifetimes. The allocations are
GFP_KERNEL_ACCOUNT, so the charge also outlives the exiting process and
pins dying memcgs.
Fix by clearing the debug data on vCPU destruction. Calling it
unconditionally is fine: struct kvm_vcpu is zero allocated, so for a vCPU
that never enabled debugging the counters are 0 and the pointers NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: s390: Zero initialize data structures for inject_pfault_token
__kvm_inject_pfault_token() only sets .type and .u.ext.ext_params2 of
the on-stack struct kvm_s390_irq but the full ext substructure is copied
into the cpu local variable on inject. ext_params and pad contain stale
stack values.
Interrupt delivery only uses ext_params2, so nothing leaks to the guest,
but a host user can use the migration ioctls to get to the data.
Fix by zero-initializing the irq struct.
Do the same for the inti data structure. |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Handle VNCR TLB invalidation race with vcpu_put() VNCR unmapping
While VNCR TLB invalidation always occurs under the MMU lock,
vcpu_put() doesn't, while it unmaps the VNCR page.
The problem is that the invalidation evaluates vncr_tlb::cpu to
decide whether an unmapping needs to take place (cpu != -1) before
performing it. On the other hand, this_cpu_reset_vncr_fixmap()
unconditionally unmaps if L1_VNCR_MAPPED is set.
These two obviously can race, with a TOCTOU pattern on the TLBI
path, and a BUG_ON() on the vcpu_put() path. And the two can end-up
calling vncr_fixmap(-1), with extra lethal effects.
Move the reset of vncr_tlb::cpu to -1 to a common function, and make
this update atomic so that only a single thread can reset the field
and perform the corresponding unmap. The vcpu_put() still need to
unconditionally unmap the current VNCR to close another ugly race.
Finally, the assignment of vncr_tlb::cpu is moved to be kept in sync
with the actual mapping, similar to L1_VNCR_MAPPED being set. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: KVM: Free init resources if kvm_init() fails
kvm_loongarch_init() calls kvm_loongarch_env_init() to allocate the
per-CPU kvm_context (vmcs) and kvm_loongarch_ops and to register the
perf callbacks, and then calls kvm_init(). If kvm_init() fails its
result is returned directly, but since module_init() does not run the
module_exit() stuff on failure, so kvm_loongarch_env_exit() is never
called and those resources are leaked.
So call kvm_loongarch_env_exit() when kvm_init() fails, matching the
teardown-on-failure pattern used by riscv_kvm_init(). |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: BPF: Move arena register slot below TCC context
Currently, the stack layout places the optional arena register slot
above the tail call counter context. When arena_vm_start is dynamically
enabled, it shifts the relative offset of the tcc_ptr slot within the
stack frame, causing hardcoded tracking macros to mismatch and leading
to memory misalignment or corruption potentially.
To fix this, move the arena register save and restore sequences below
the tail call counter context slots in both build_prologue() and the
epilogue.
Update __build_epilogue() to insert a proper offset decrement to safely
skip the unneeded tcc_ptr reading block while accurately aligning with
the relocated arena slot at the very bottom.
With this patch, the tcc_ptr slot is always positioned at a fixed
distance directly underneath the base callee-saved registers that is
independent of whether the arena features are on. |
| In the Linux kernel, the following vulnerability has been resolved:
media: airspy: use vb2_video_unregister_device() on disconnect to fix NULL deref
airspy_disconnect() clears s->udev under v4l2_lock, but
airspy_stop_streaming() unconditionally calls airspy_ctrl_msg() and
airspy_free_stream_bufs() afterwards. If a streaming user closes the
device after disconnect, stop_streaming() runs and dereferences the
NULL s->udev:
airspy_stop_streaming()
airspy_ctrl_msg(s, CMD_RECEIVER_MODE, 0, 0, NULL, 0)
usb_sndctrlpipe(s->udev, 0) /* NULL deref */
airspy_free_stream_bufs(s)
usb_free_coherent(s->udev, ...) /* NULL deref */
The airspy driver uses vb2_fop_release() in its file_operations, so
replace video_unregister_device(&s->vdev) with
vb2_video_unregister_device(&s->vdev) and move it before clearing
s->udev. vb2_video_unregister_device() releases the vb2 queue, which
synchronously runs airspy_stop_streaming() if streaming is active, so
the URBs, coherent DMA stream buffers and the hardware stop control
message all execute while s->udev is still valid.
vb2_video_unregister_device() locks vdev->queue->lock (vb_queue_lock)
internally, and stop_streaming() locks v4l2_lock, so the previous outer
mutex_lock(&s->vb_queue_lock) / mutex_lock(&s->v4l2_lock) pair around
the unregister sequence would self-deadlock and has been removed. A
short v4l2_lock critical section around s->udev = NULL remains so any
ioctl path that still holds the file descriptor sees coherent state.
Issue identified by automated review of the INV-003 series at
https://sashiko.dev/ |
| In the Linux kernel, the following vulnerability has been resolved:
media: cec: core: Fix kmemleak due to missed rc_free_device() call
The commit dccc0c3ddf8f ("media: rc: fix race between unregister and
urb/irq callbacks") removed the implicit call to rc_free_device() from
rc_unregister_device(). However, the commit missed to remove the NULL
assignment of adap->rc that is now causing rc_free_device() to never be
called on an allocated rc device.
kmemleak reports following after e.g. dw-hdmi unbind:
unreferenced object 0xffff00010ac10000 (size 4096):
comm "kworker/u16:1", pid 39, jiffies 4294897739
hex dump (first 32 bytes):
20 23 4b 0a 01 00 ff ff 08 00 c1 0a 01 00 ff ff #K.............
08 00 c1 0a 01 00 ff ff 00 00 00 00 00 00 00 00 ................
backtrace (crc e11baccc):
kmemleak_alloc+0x38/0x44
__kmalloc_cache_noprof+0x4a8/0x5e0
rc_allocate_device+0x48/0x2a0
cec_allocate_adapter+0x3ac/0x800
dw_hdmi_cec_probe+0x264/0x634
platform_probe+0xc0/0x188
really_probe+0x4a4/0x8e0
__driver_probe_device+0x2f8/0x440
driver_probe_device+0x60/0x160
__device_attach_driver+0x1a0/0x2a0
bus_for_each_drv+0x100/0x1a0
__device_attach+0x174/0x350
device_initial_probe+0x90/0xb0
bus_probe_device+0x4c/0x120
device_add+0xdec/0x116c
platform_device_add+0x354/0x598
Remove the assignment of adap->rc to NULL to let cec_delete_adapter()
free the allocated rc device after last user of the cec device exits to
fix the kmemleak. |
| In the Linux kernel, the following vulnerability has been resolved:
media: cedrus: fix memory leak in cedrus_init_ctrls()
In cedrus_init_ctrls(), the V4L2 control handler is initialized before
allocating memory for ctx->ctrls. If this allocation fails, the function
returns -ENOMEM without freeing the previously allocated handler
resources, leading to a memory leak.
Fix this by calling v4l2_ctrl_handler_free() on the ctx->ctrls allocation
failure path.
The bug was first flagged by an experimental analysis tool we are
developing for kernel memory-management bugs while analyzing
v6.13-rc1. The tool is still under development and is not yet publicly
available. Manual inspection confirms that the bug is still
present in v7.1.1.
An x86_64 allyesconfig build showed no new warnings. As we do not have an
Allwinner SoC or board with a Cedrus VPU available to test with, no
runtime testing was able to be performed. |
