| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
dm-pcache: fix use-after-free and invalid seg operations in kset_replay()
In kset_replay, when key->seg_gen is stale (key->seg_gen <
key->cache_pos.cache_seg->gen), cache_key_put(key) is called but then
key->cache_pos.cache_seg is accessed as the argument to cache_seg_get().
This is a use-after-free on the freed key memory. Although mempool
recycled memory is not immediately reclaimed or overwritten in practice,
this is still a potential UAF bug.
Additionally, for expired invalid keys, setting the cache->seg_map bit
and calling cache_seg_get() is unreasonable since the corresponding
segment data is no longer valid.
Fix both issues by moving cache_seg_get() and __set_bit() after the
gen check, so they only execute for valid keys, and using continue to
skip invalid keys. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: Fix unlocked dereference of dev->desc in i3c_device_get_supported_xfer_mode()
i3c_device_get_supported_xfer_mode() uses dev->desc to obtain the
master controller. However, dev->desc must not be dereferenced unless
bus->lock is held, and this function does not take that lock.
The function only needs access to the master controller associated with
the device's bus. Use dev->bus instead, which is always valid for the
lifetime of the device and does not require dereferencing dev->desc. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: adi: initialize the lock before enabling interrupts
adi_i3c_master_probe() requests the IRQ and unmasks REG_IRQ_PENDING_CMDR
before the controller's IBI state, transfer queue list and transfer
queue lock are initialized. A pending CMDR interrupt can therefore run
adi_i3c_master_irq() and take master->xferqueue.lock before the dynamic
lock has been initialized.
This issue was found by our static analysis tool and then manually
reviewed against the current tree.
The grounded PoC kept the probe ordering and the IRQ path
adi_i3c_master_probe() -> adi_i3c_master_irq() -> xferqueue.lock, with a
pending CMDR interrupt arriving after REG_IRQ_PENDING_CMDR is unmasked.
Lockdep reported:
INFO: trying to register non-static key.
you didn't initialize this object before use?
lock_acquire+0xbb/0x290
_raw_spin_lock_irqsave+0x36/0x60
adi_i3c_master_irq+0x32/0x56 [vuln_msv]
adi_i3c_master_probe+0x5a/0xf47 [vuln_msv]
Initialize the transfer queue and IBI state before requesting and
unmasking the IRQ. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: renesas: Check that the transfer is valid before accessing it
The Renesas I3C driver uses an asynchronous model to transfer data. It
prepares a struct renesas_i3c_xfer, enqueues it, and waits for completion.
The interrupt handler dequeues the transfer, updates/uses it, and signals
the waiting thread.
If the completion times out, the waiting thread dequeues the transfer and
free it. If an interrupt fires after that, the handler may access freed
memory, leading to crashes.
Check that the transfer is still valid before accessing it in the
interrupt handler. With it clear any status flags and disable all
the interrupts to avoid triggering the same interrupts again. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtl8xxxu: fix use-after-free from rx_urb_wq on stop
rtl8xxxu arms rx_urb_wq from the RX completion path:
rtl8xxxu_rx_complete() hands the URB to rtl8xxxu_queue_rx_urb(), which
queues it on rx_urb_pending_list and, once the list grows past
RTL8XXXU_RX_URB_PENDING_WATER, schedules rx_urb_wq. The worker
rtl8xxxu_rx_urb_work() drains rx_urb_pending_list, recovers priv through
container_of, and resubmits each URB through rtl8xxxu_submit_rx_urb(),
which anchors it on rx_anchor and dereferences priv->udev.
rtl8xxxu_stop() cancels the sibling work items (c2hcmd_work, ra_watchdog,
update_beacon_work) but never cancels rx_urb_wq, so a worker armed during
the last burst of RX traffic can run rtl8xxxu_rx_urb_work() after
rtl8xxxu_disconnect() has called ieee80211_free_hw(), which frees priv,
producing a use-after-free. The window opens under active RX traffic
(pending count above the watermark) followed by a disconnect.
There are two teardown races to close:
* rtl8xxxu_queue_rx_urb() decided whether to enqueue under rx_urb_lock
but called schedule_work() after dropping the lock. A completion
that observed shutdown == false and released the lock could then call
schedule_work() after rtl8xxxu_stop() had set shutdown and
cancel_work_sync() had already returned, arming the worker to run
after the teardown. Move schedule_work() under the same !shutdown
branch so the arming decision is atomic with the shutdown check.
* rtl8xxxu_rx_urb_work() anchors every URB it drained back onto
rx_anchor through rtl8xxxu_submit_rx_urb(). A worker still running
when usb_kill_anchored_urbs(&priv->rx_anchor) returned would submit a
URB that escaped the kill. In rtl8xxxu_stop(), call
cancel_work_sync(&priv->rx_urb_wq) before the kill so the worker is
drained first.
After priv->shutdown is set under rx_urb_lock, completions can no longer
queue rx_urb_wq. cancel_work_sync() then drains the last queued or running
worker, and the following usb_kill_anchored_urbs() kills the URBs it may
have submitted.
rtl8xxxu_disconnect() is covered because ieee80211_unregister_hw()
guarantees .stop() runs for a live interface before ieee80211_free_hw()
frees priv. The probe error path needs no cancel: rx_urb_wq is
INIT_WORK()'d there but cannot have been scheduled, since no URB is
submitted before ieee80211_register_hw() succeeds.
This bug was found by static analysis. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rtlwifi: rtl8192du: check QoS TID before indexing tids
rtl92du_tx_fill_desc() uses ieee80211_get_tid() to read the QoS TID
from the 802.11 header and then uses it as an index into
sta_entry->tids[]. ieee80211_get_tid() returns the low 4-bit QoS TID
value, so the result can be in the range 0..15.
rtlwifi only allocates MAX_TID_COUNT entries for sta_entry->tids[], and
MAX_TID_COUNT is 9. A QoS TID greater than 8 therefore indexes past the
aggregation state array. Keep the default RTL_AGG_STOP state for
out-of-range TIDs, matching rtl92cu_tx_fill_desc().
This issue was detected by our static analysis tool and confirmed by
manual audit. UBSAN validation for the same bug pattern reports an
array-index-out-of-bounds access with index 10 for type
'rtl_tid_data [9]'. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: bound the device EEPROM address before the EFUSE copy
mt7915_mcu_get_eeprom() copies a fixed EFUSE block into the driver's
dev->mt76.eeprom.data buffer at the offset reported by the MCU response
(res->addr, a device-controlled __le32) without checking it against the
buffer size. A malicious or malfunctioning device can report an arbitrary
address and drive a 16-byte out-of-bounds write past eeprom.data.
Reject a response whose address would place the copy outside eeprom.data
before deriving the destination pointer. Devices that echo the requested
in-bounds offset are unaffected. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: cancel mlo_pm_work on stop
mt7925 queues mlo_pm_work with a 5 second delay during multi-link
power-save setup and never cancels it on the stop path. If the device is
torn down inside that window, the work outlives the teardown and its timer
fires afterwards, trying to queue onto the workqueue that is already gone:
workqueue: cannot queue mt7925_mlo_pm_work [mt7925_common] on wq phy0
WARNING: kernel/workqueue.c:2283 at __queue_work+0x59/0xa0, CPU#1: swapper/1/0
call_timer_fn+0x2a/0x140
__run_timers+0x203/0x330
run_timer_softirq+0x86/0xf0
mt7921 already has its own stop callback, so add one for mt7925 that
cancels the work before calling mt792x_stop(). mt7925_ops backs both the
PCIe and USB drivers, so this covers both. |
| In the Linux kernel, the following vulnerability has been resolved:
sysctl: move the "cad_pid" entry from pid_table[] to kern_reboot_table[]
cad_pid is global, and kill_cad_pid() is only used in the root namespace.
However, due to pid_table_root_permissions(), a non-root user can unshare
pid/user namespaces and modify it from the child namespace. This makes no
sense and is simply wrong.
Move it to kern_reboot_table[] where it logically belongs; this ensures
that only GLOBAL_ROOT_UID can read/modify this sysctl.
Note that this patch doesn't preserve "#ifdef CONFIG_PROC_SYSCTL" around
the "cad_pid"; CONFIG_PROC_SYSCTL selects CONFIG_SYSCTL, so it is always
set when kern_reboot_table[] is compiled. |
| Heap-based buffer overflow in Microsoft Office Word allows an unauthorized attacker to execute code over a network. |
| Heap-based buffer overflow in SQL Server allows an authorized attacker to execute code over a network. |
| Adobe Commerce is affected by an Improper Limitation of a Pathname to a Restricted Directory ('Path Traversal') vulnerability that could result in a Security feature bypass. An attacker with high privileges could leverage this vulnerability to access unauthorized files or directories outside the intended restrictions, causing a limited disruption to availability. Exploitation of this issue does not require user interaction. Scope is changed. |
| Editor SQL Injection in Sky Addons for Elementor <= 3.8.4 versions. |
| A flaw was found in Keycloak Policy Enforcer. This vulnerability allows any authenticated user to bypass all authorization policies, including role, scope, and User-Managed Access (UMA) permission checks. By including the configured access-denied page path within a request URL, either as a path segment or a query parameter, an attacker can gain unauthorized access to protected resources. |
| A race condition in the document value layer of MongoDB Server can allow concurrent server threads to operate on the same internal memory without synchronization, leading to memory corruption. An authenticated user holding ordinary read-write privileges on a database may be able to trigger this condition over the normal client protocol, resulting in server termination and potential corruption of process memory with user-influenced content. Successful use of this issue may impact the confidentiality, integrity, and availability of the affected server process. |
| The Booking for Appointments and Events Calendar WordPress plugin before 2.4.10 does not verify that the user editing a customer or employee record is entitled to modify the WordPress account linked to it, allowing users holding Amelia's customer or employee management permissions to set the password and email address of other users' WordPress accounts and take them over. |
| The Temporary Login Without Password WordPress plugin before 1.9.9 does not verify that the user requesting a temporary login holds network super admin rights before granting the new account those rights, allowing an administrator of a single site on a multisite network to take over the whole network. The same missing check also allows an existing account, including the attacker's own, to be promoted. |
| The Yogeta WP Cloud WordPress plugin through 1.0 does not validate a user-supplied file path before passing it to a file-read function on a public endpoint that lacks any authorization check, allowing unauthenticated attackers to download arbitrary files from the server, including files containing sensitive credentials. |
| The Export & Import WPBakery Page Builder WordPress plugin through 1.0.2 does not perform any CSRF check on its template-import feature and does not sanitise the imported data before storing it and echoing it back, allowing attackers to make a logged-in administrator import a crafted template via a forged request that results in Stored Cross-Site Scripting executed in the administrator's session. |
| The BE REST Endpoints WordPress plugin through 1.0.0 does not perform any authorization check before allowing widgets to be read, created, updated and deleted, and does not sanitize the values it stores in them, allowing unauthenticated users to inject arbitrary web scripts which will execute in the browser of any user visiting the site. |
