| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: storage: Fix memory leak in USB bulk transport
A kernel memory leak was identified by the 'ioctl_sg01' test from Linux
Test Project (LTP). The following bytes were mainly observed: 0x53425355.
When USB storage devices incorrectly skip the data phase with status data,
the code extracts/validates the CSW from the sg buffer, but fails to clear
it afterwards. This leaves status protocol data in srb's transfer buffer,
such as the US_BULK_CS_SIGN 'USBS' signature observed here. Thus, this can
lead to USB protocols leaks to user space through SCSI generic (/dev/sg*)
interfaces, such as the one seen here when the LTP test requested 512 KiB.
Fix the leak by zeroing the CSW data in srb's transfer buffer immediately
after the validation of devices that skip data phase.
Note: Differently from CVE-2018-1000204, which fixed a big leak by zero-
ing pages at allocation time, this leak occurs after allocation, when USB
protocol data is written to already-allocated sg pages. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Fix LTP test failures when timestamps are delegated
The utimes01 and utime06 tests fail when delegated timestamps are
enabled, specifically in subtests that modify the atime and mtime
fields using the 'nobody' user ID.
The problem can be reproduced as follow:
# echo "/media *(rw,no_root_squash,sync)" >> /etc/exports
# export -ra
# mount -o rw,nfsvers=4.2 127.0.0.1:/media /tmpdir
# cd /opt/ltp
# ./runltp -d /tmpdir -s utimes01
# ./runltp -d /tmpdir -s utime06
This issue occurs because nfs_setattr does not verify the inode's
UID against the caller's fsuid when delegated timestamps are
permitted for the inode.
This patch adds the UID check and if it does not match then the
request is sent to the server for permission checking. |
| In the Linux kernel, the following vulnerability has been resolved:
net: netpoll: fix incorrect refcount handling causing incorrect cleanup
commit efa95b01da18 ("netpoll: fix use after free") incorrectly
ignored the refcount and prematurely set dev->npinfo to NULL during
netpoll cleanup, leading to improper behavior and memory leaks.
Scenario causing lack of proper cleanup:
1) A netpoll is associated with a NIC (e.g., eth0) and netdev->npinfo is
allocated, and refcnt = 1
- Keep in mind that npinfo is shared among all netpoll instances. In
this case, there is just one.
2) Another netpoll is also associated with the same NIC and
npinfo->refcnt += 1.
- Now dev->npinfo->refcnt = 2;
- There is just one npinfo associated to the netdev.
3) When the first netpolls goes to clean up:
- The first cleanup succeeds and clears np->dev->npinfo, ignoring
refcnt.
- It basically calls `RCU_INIT_POINTER(np->dev->npinfo, NULL);`
- Set dev->npinfo = NULL, without proper cleanup
- No ->ndo_netpoll_cleanup() is either called
4) Now the second target tries to clean up
- The second cleanup fails because np->dev->npinfo is already NULL.
* In this case, ops->ndo_netpoll_cleanup() was never called, and
the skb pool is not cleaned as well (for the second netpoll
instance)
- This leaks npinfo and skbpool skbs, which is clearly reported by
kmemleak.
Revert commit efa95b01da18 ("netpoll: fix use after free") and adds
clarifying comments emphasizing that npinfo cleanup should only happen
once the refcount reaches zero, ensuring stable and correct netpoll
behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
vmw_balloon: indicate success when effectively deflating during migration
When migrating a balloon page, we first deflate the old page to then
inflate the new page.
However, if inflating the new page succeeded, we effectively deflated the
old page, reducing the balloon size.
In that case, the migration actually worked: similar to migrating+
immediately deflating the new page. The old page will be freed back to
the buddy.
Right now, the core will leave the page be marked as isolated (as we
returned an error). When later trying to putback that page, we will run
into the WARN_ON_ONCE() in balloon_page_putback().
That handling was changed in commit 3544c4faccb8 ("mm/balloon_compaction:
stop using __ClearPageMovable()"); before that change, we would have
tolerated that way of handling it.
To fix it, let's just return 0 in that case, making the core effectively
just clear the "isolated" flag + freeing it back to the buddy as if the
migration succeeded. Note that the new page will also get freed when the
core puts the last reference.
Note that this also makes it all be more consistent: we will no longer
unisolate the page in the balloon driver while keeping it marked as being
isolated in migration core.
This was found by code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: check device's attached status in compat ioctls
Syzbot identified an issue [1] that crashes kernel, seemingly due to
unexistent callback dev->get_valid_routes(). By all means, this should
not occur as said callback must always be set to
get_zero_valid_routes() in __comedi_device_postconfig().
As the crash seems to appear exclusively in i386 kernels, at least,
judging from [1] reports, the blame lies with compat versions
of standard IOCTL handlers. Several of them are modified and
do not use comedi_unlocked_ioctl(). While functionality of these
ioctls essentially copy their original versions, they do not
have required sanity check for device's attached status. This,
in turn, leads to a possibility of calling select IOCTLs on a
device that has not been properly setup, even via COMEDI_DEVCONFIG.
Doing so on unconfigured devices means that several crucial steps
are missed, for instance, specifying dev->get_valid_routes()
callback.
Fix this somewhat crudely by ensuring device's attached status before
performing any ioctls, improving logic consistency between modern
and compat functions.
[1] Syzbot report:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CR2: ffffffffffffffd6 CR3: 000000006c717000 CR4: 0000000000352ef0
Call Trace:
<TASK>
get_valid_routes drivers/comedi/comedi_fops.c:1322 [inline]
parse_insn+0x78c/0x1970 drivers/comedi/comedi_fops.c:1401
do_insnlist_ioctl+0x272/0x700 drivers/comedi/comedi_fops.c:1594
compat_insnlist drivers/comedi/comedi_fops.c:3208 [inline]
comedi_compat_ioctl+0x810/0x990 drivers/comedi/comedi_fops.c:3273
__do_compat_sys_ioctl fs/ioctl.c:695 [inline]
__se_compat_sys_ioctl fs/ioctl.c:638 [inline]
__ia32_compat_sys_ioctl+0x242/0x370 fs/ioctl.c:638
do_syscall_32_irqs_on arch/x86/entry/syscall_32.c:83 [inline]
... |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: multiq3: sanitize config options in multiq3_attach()
Syzbot identified an issue [1] in multiq3_attach() that induces a
task timeout due to open() or COMEDI_DEVCONFIG ioctl operations,
specifically, in the case of multiq3 driver.
This problem arose when syzkaller managed to craft weird configuration
options used to specify the number of channels in encoder subdevice.
If a particularly great number is passed to s->n_chan in
multiq3_attach() via it->options[2], then multiple calls to
multiq3_encoder_reset() at the end of driver-specific attach() method
will be running for minutes, thus blocking tasks and affected devices
as well.
While this issue is most likely not too dangerous for real-life
devices, it still makes sense to sanitize configuration inputs. Enable
a sensible limit on the number of encoder chips (4 chips max, each
with 2 channels) to stop this behaviour from manifesting.
[1] Syzbot crash:
INFO: task syz.2.19:6067 blocked for more than 143 seconds.
...
Call Trace:
<TASK>
context_switch kernel/sched/core.c:5254 [inline]
__schedule+0x17c4/0x4d60 kernel/sched/core.c:6862
__schedule_loop kernel/sched/core.c:6944 [inline]
schedule+0x165/0x360 kernel/sched/core.c:6959
schedule_preempt_disabled+0x13/0x30 kernel/sched/core.c:7016
__mutex_lock_common kernel/locking/mutex.c:676 [inline]
__mutex_lock+0x7e6/0x1350 kernel/locking/mutex.c:760
comedi_open+0xc0/0x590 drivers/comedi/comedi_fops.c:2868
chrdev_open+0x4cc/0x5e0 fs/char_dev.c:414
do_dentry_open+0x953/0x13f0 fs/open.c:965
vfs_open+0x3b/0x340 fs/open.c:1097
... |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Don't skip unrelated instruction if INT3/INTO is replaced
When re-injecting a soft interrupt from an INT3, INT0, or (select) INTn
instruction, discard the exception and retry the instruction if the code
stream is changed (e.g. by a different vCPU) between when the CPU
executes the instruction and when KVM decodes the instruction to get the
next RIP.
As effectively predicted by commit 6ef88d6e36c2 ("KVM: SVM: Re-inject
INT3/INTO instead of retrying the instruction"), failure to verify that
the correct INTn instruction was decoded can effectively clobber guest
state due to decoding the wrong instruction and thus specifying the
wrong next RIP.
The bug most often manifests as "Oops: int3" panics on static branch
checks in Linux guests. Enabling or disabling a static branch in Linux
uses the kernel's "text poke" code patching mechanism. To modify code
while other CPUs may be executing that code, Linux (temporarily)
replaces the first byte of the original instruction with an int3 (opcode
0xcc), then patches in the new code stream except for the first byte,
and finally replaces the int3 with the first byte of the new code
stream. If a CPU hits the int3, i.e. executes the code while it's being
modified, then the guest kernel must look up the RIP to determine how to
handle the #BP, e.g. by emulating the new instruction. If the RIP is
incorrect, then this lookup fails and the guest kernel panics.
The bug reproduces almost instantly by hacking the guest kernel to
repeatedly check a static branch[1] while running a drgn script[2] on
the host to constantly swap out the memory containing the guest's TSS.
[1]: https://gist.github.com/osandov/44d17c51c28c0ac998ea0334edf90b5a
[2]: https://gist.github.com/osandov/10e45e45afa29b11e0c7209247afc00b |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: zstd - fix double-free in per-CPU stream cleanup
The crypto/zstd module has a double-free bug that occurs when multiple
tfms are allocated and freed.
The issue happens because zstd_streams (per-CPU contexts) are freed in
zstd_exit() during every tfm destruction, rather than being managed at
the module level. When multiple tfms exist, each tfm exit attempts to
free the same shared per-CPU streams, resulting in a double-free.
This leads to a stack trace similar to:
BUG: Bad page state in process kworker/u16:1 pfn:106fd93
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x106fd93
flags: 0x17ffffc0000000(node=0|zone=2|lastcpupid=0x1fffff)
page_type: 0xffffffff()
raw: 0017ffffc0000000 dead000000000100 dead000000000122 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: nonzero entire_mapcount
Modules linked in: ...
CPU: 3 UID: 0 PID: 2506 Comm: kworker/u16:1 Kdump: loaded Tainted: G B
Hardware name: ...
Workqueue: btrfs-delalloc btrfs_work_helper
Call Trace:
<TASK>
dump_stack_lvl+0x5d/0x80
bad_page+0x71/0xd0
free_unref_page_prepare+0x24e/0x490
free_unref_page+0x60/0x170
crypto_acomp_free_streams+0x5d/0xc0
crypto_acomp_exit_tfm+0x23/0x50
crypto_destroy_tfm+0x60/0xc0
...
Change the lifecycle management of zstd_streams to free the streams only
once during module cleanup. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/memfd: fix information leak in hugetlb folios
When allocating hugetlb folios for memfd, three initialization steps are
missing:
1. Folios are not zeroed, leading to kernel memory disclosure to userspace
2. Folios are not marked uptodate before adding to page cache
3. hugetlb_fault_mutex is not taken before hugetlb_add_to_page_cache()
The memfd allocation path bypasses the normal page fault handler
(hugetlb_no_page) which would handle all of these initialization steps.
This is problematic especially for udmabuf use cases where folios are
pinned and directly accessed by userspace via DMA.
Fix by matching the initialization pattern used in hugetlb_no_page():
- Zero the folio using folio_zero_user() which is optimized for huge pages
- Mark it uptodate with folio_mark_uptodate()
- Take hugetlb_fault_mutex before adding to page cache to prevent races
The folio_zero_user() change also fixes a potential security issue where
uninitialized kernel memory could be disclosed to userspace through read()
or mmap() operations on the memfd. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer
When a UAS device is unplugged during data transfer, there is
a probability of a system panic occurring. The root cause is
an access to an invalid memory address during URB callback handling.
Specifically, this happens when the dma_direct_unmap_sg() function
is called within the usb_hcd_unmap_urb_for_dma() interface, but the
sg->dma_address field is 0 and the sg data structure has already been
freed.
The SCSI driver sends transfer commands by invoking uas_queuecommand_lck()
in uas.c, using the uas_submit_urbs() function to submit requests to USB.
Within the uas_submit_urbs() implementation, three URBs (sense_urb,
data_urb, and cmd_urb) are sequentially submitted. Device removal may
occur at any point during uas_submit_urbs execution, which may result
in URB submission failure. However, some URBs might have been successfully
submitted before the failure, and uas_submit_urbs will return the -ENODEV
error code in this case. The current error handling directly calls
scsi_done(). In the SCSI driver, this eventually triggers scsi_complete()
to invoke scsi_end_request() for releasing the sgtable. The successfully
submitted URBs, when being unlinked to giveback, call
usb_hcd_unmap_urb_for_dma() in hcd.c, leading to exceptions during sg
unmapping operations since the sg data structure has already been freed.
This patch modifies the error condition check in the uas_submit_urbs()
function. When a UAS device is removed but one or more URBs have already
been successfully submitted to USB, it avoids immediately invoking
scsi_done() and save the cmnd to devinfo->cmnd array. If the successfully
submitted URBs is completed before devinfo->resetting being set, then
the scsi_done() function will be called within uas_try_complete() after
all pending URB operations are finalized. Otherwise, the scsi_done()
function will be called within uas_zap_pending(), which is executed after
usb_kill_anchored_urbs().
The error handling only takes effect when uas_queuecommand_lck() calls
uas_submit_urbs() and returns the error value -ENODEV . In this case,
the device is disconnected, and the flow proceeds to uas_disconnect(),
where uas_zap_pending() is invoked to call uas_try_complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
iio: accel: bmc150: Fix irq assumption regression
The code in bmc150-accel-core.c unconditionally calls
bmc150_accel_set_interrupt() in the iio_buffer_setup_ops,
such as on the runtime PM resume path giving a kernel
splat like this if the device has no interrupts:
Unable to handle kernel NULL pointer dereference at virtual
address 00000001 when read
PC is at bmc150_accel_set_interrupt+0x98/0x194
LR is at __pm_runtime_resume+0x5c/0x64
(...)
Call trace:
bmc150_accel_set_interrupt from bmc150_accel_buffer_postenable+0x40/0x108
bmc150_accel_buffer_postenable from __iio_update_buffers+0xbe0/0xcbc
__iio_update_buffers from enable_store+0x84/0xc8
enable_store from kernfs_fop_write_iter+0x154/0x1b4
This bug seems to have been in the driver since the beginning,
but it only manifests recently, I do not know why.
Store the IRQ number in the state struct, as this is a common
pattern in other drivers, then use this to determine if we have
IRQ support or not. |
| In the Linux kernel, the following vulnerability has been resolved:
sched_ext: Fix scx_enable() crash on helper kthread creation failure
A crash was observed when the sched_ext selftests runner was
terminated with Ctrl+\ while test 15 was running:
NIP [c00000000028fa58] scx_enable.constprop.0+0x358/0x12b0
LR [c00000000028fa2c] scx_enable.constprop.0+0x32c/0x12b0
Call Trace:
scx_enable.constprop.0+0x32c/0x12b0 (unreliable)
bpf_struct_ops_link_create+0x18c/0x22c
__sys_bpf+0x23f8/0x3044
sys_bpf+0x2c/0x6c
system_call_exception+0x124/0x320
system_call_vectored_common+0x15c/0x2ec
kthread_run_worker() returns an ERR_PTR() on failure rather than NULL,
but the current code in scx_alloc_and_add_sched() only checks for a NULL
helper. Incase of failure on SIGQUIT, the error is not handled in
scx_alloc_and_add_sched() and scx_enable() ends up dereferencing an
error pointer.
Error handling is fixed in scx_alloc_and_add_sched() to propagate
PTR_ERR() into ret, so that scx_enable() jumps to the existing error
path, avoiding random dereference on failure. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/notify: call exportfs_encode_fid with s_umount
Calling intotify_show_fdinfo() on fd watching an overlayfs inode, while
the overlayfs is being unmounted, can lead to dereferencing NULL ptr.
This issue was found by syzkaller.
Race Condition Diagram:
Thread 1 Thread 2
-------- --------
generic_shutdown_super()
shrink_dcache_for_umount
sb->s_root = NULL
|
| vfs_read()
| inotify_fdinfo()
| * inode get from mark *
| show_mark_fhandle(m, inode)
| exportfs_encode_fid(inode, ..)
| ovl_encode_fh(inode, ..)
| ovl_check_encode_origin(inode)
| * deref i_sb->s_root *
|
|
v
fsnotify_sb_delete(sb)
Which then leads to:
[ 32.133461] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 32.134438] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 32.135032] CPU: 1 UID: 0 PID: 4468 Comm: systemd-coredum Not tainted 6.17.0-rc6 #22 PREEMPT(none)
<snip registers, unreliable trace>
[ 32.143353] Call Trace:
[ 32.143732] ovl_encode_fh+0xd5/0x170
[ 32.144031] exportfs_encode_inode_fh+0x12f/0x300
[ 32.144425] show_mark_fhandle+0xbe/0x1f0
[ 32.145805] inotify_fdinfo+0x226/0x2d0
[ 32.146442] inotify_show_fdinfo+0x1c5/0x350
[ 32.147168] seq_show+0x530/0x6f0
[ 32.147449] seq_read_iter+0x503/0x12a0
[ 32.148419] seq_read+0x31f/0x410
[ 32.150714] vfs_read+0x1f0/0x9e0
[ 32.152297] ksys_read+0x125/0x240
IOW ovl_check_encode_origin derefs inode->i_sb->s_root, after it was set
to NULL in the unmount path.
Fix it by protecting calling exportfs_encode_fid() from
show_mark_fhandle() with s_umount lock.
This form of fix was suggested by Amir in [1].
[1]: https://lore.kernel.org/all/CAOQ4uxhbDwhb+2Brs1UdkoF0a3NSdBAOQPNfEHjahrgoKJpLEw@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: directly free partially initialized fs_info in btrfs_check_leaked_roots()
If fs_info->super_copy or fs_info->super_for_commit allocated failed in
btrfs_get_tree_subvol(), then no need to call btrfs_free_fs_info().
Otherwise btrfs_check_leaked_roots() would access NULL pointer because
fs_info->allocated_roots had not been initialised.
syzkaller reported the following information:
------------[ cut here ]------------
BUG: unable to handle page fault for address: fffffffffffffbb0
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 64c9067 P4D 64c9067 PUD 64cb067 PMD 0
Oops: Oops: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 1402 Comm: syz.1.35 Not tainted 6.15.8 #4 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), (...)
RIP: 0010:arch_atomic_read arch/x86/include/asm/atomic.h:23 [inline]
RIP: 0010:raw_atomic_read include/linux/atomic/atomic-arch-fallback.h:457 [inline]
RIP: 0010:atomic_read include/linux/atomic/atomic-instrumented.h:33 [inline]
RIP: 0010:refcount_read include/linux/refcount.h:170 [inline]
RIP: 0010:btrfs_check_leaked_roots+0x18f/0x2c0 fs/btrfs/disk-io.c:1230
[...]
Call Trace:
<TASK>
btrfs_free_fs_info+0x310/0x410 fs/btrfs/disk-io.c:1280
btrfs_get_tree_subvol+0x592/0x6b0 fs/btrfs/super.c:2029
btrfs_get_tree+0x63/0x80 fs/btrfs/super.c:2097
vfs_get_tree+0x98/0x320 fs/super.c:1759
do_new_mount+0x357/0x660 fs/namespace.c:3899
path_mount+0x716/0x19c0 fs/namespace.c:4226
do_mount fs/namespace.c:4239 [inline]
__do_sys_mount fs/namespace.c:4450 [inline]
__se_sys_mount fs/namespace.c:4427 [inline]
__x64_sys_mount+0x28c/0x310 fs/namespace.c:4427
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0x92/0x180 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f032eaffa8d
[...] |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: fix module removal if firmware download failed
Fix remove if firmware failed to load:
qcom-iris aa00000.video-codec: Direct firmware load for qcom/vpu/vpu33_p4.mbn failed with error -2
qcom-iris aa00000.video-codec: firmware download failed
qcom-iris aa00000.video-codec: core init failed
then:
$ echo aa00000.video-codec > /sys/bus/platform/drivers/qcom-iris/unbind
Triggers:
genpd genpd:1:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
video_cc_mvs0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#1: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
------------[ cut here ]------------
video_cc_mvs0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#2: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu_power_off_hw+0x48/0x58 [qcom_iris]
iris_vpu33_power_off_hardware+0x44/0x230 [qcom_iris]
iris_vpu_power_off+0x34/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
genpd genpd:0:aa00000.video-codec: Runtime PM usage count underflow!
------------[ cut here ]------------
gcc_video_axi0_clk already disabled
WARNING: drivers/clk/clk.c:1206 at clk_core_disable+0xa4/0xac, CPU#4: sh/542
<snip>
pc : clk_core_disable+0xa4/0xac
lr : clk_core_disable+0xa4/0xac
<snip>
Call trace:
clk_core_disable+0xa4/0xac (P)
clk_disable+0x30/0x4c
iris_disable_unprepare_clock+0x20/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
------------[ cut here ]------------
gcc_video_axi0_clk already unprepared
WARNING: drivers/clk/clk.c:1065 at clk_core_unprepare+0xf0/0x110, CPU#4: sh/542
<snip>
pc : clk_core_unprepare+0xf0/0x110
lr : clk_core_unprepare+0xf0/0x110
<snip>
Call trace:
clk_core_unprepare+0xf0/0x110 (P)
clk_unprepare+0x2c/0x44
iris_disable_unprepare_clock+0x28/0x48 [qcom_iris]
iris_vpu33_power_off_controller+0x17c/0x428 [qcom_iris]
iris_vpu_power_off+0x48/0x84 [qcom_iris]
iris_core_deinit+0x44/0xc8 [qcom_iris]
iris_remove+0x20/0x48 [qcom_iris]
platform_remove+0x20/0x30
device_remove+0x4c/0x80
<snip>
---[ end trace 0000000000000000 ]---
Skip deinit if initialization never succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: hugetlb: avoid soft lockup when mprotect to large memory area
When calling mprotect() to a large hugetlb memory area in our customer's
workload (~300GB hugetlb memory), soft lockup was observed:
watchdog: BUG: soft lockup - CPU#98 stuck for 23s! [t2_new_sysv:126916]
CPU: 98 PID: 126916 Comm: t2_new_sysv Kdump: loaded Not tainted 6.17-rc7
Hardware name: GIGACOMPUTING R2A3-T40-AAV1/Jefferson CIO, BIOS 5.4.4.1 07/15/2025
pstate: 20400009 (nzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mte_clear_page_tags+0x14/0x24
lr : mte_sync_tags+0x1c0/0x240
sp : ffff80003150bb80
x29: ffff80003150bb80 x28: ffff00739e9705a8 x27: 0000ffd2d6a00000
x26: 0000ff8e4bc00000 x25: 00e80046cde00f45 x24: 0000000000022458
x23: 0000000000000000 x22: 0000000000000004 x21: 000000011b380000
x20: ffff000000000000 x19: 000000011b379f40 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : ffffc875e0aa5e2c
x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000
x5 : fffffc01ce7a5c00 x4 : 00000000046cde00 x3 : fffffc0000000000
x2 : 0000000000000004 x1 : 0000000000000040 x0 : ffff0046cde7c000
Call trace:
mte_clear_page_tags+0x14/0x24
set_huge_pte_at+0x25c/0x280
hugetlb_change_protection+0x220/0x430
change_protection+0x5c/0x8c
mprotect_fixup+0x10c/0x294
do_mprotect_pkey.constprop.0+0x2e0/0x3d4
__arm64_sys_mprotect+0x24/0x44
invoke_syscall+0x50/0x160
el0_svc_common+0x48/0x144
do_el0_svc+0x30/0xe0
el0_svc+0x30/0xf0
el0t_64_sync_handler+0xc4/0x148
el0t_64_sync+0x1a4/0x1a8
Soft lockup is not triggered with THP or base page because there is
cond_resched() called for each PMD size.
Although the soft lockup was triggered by MTE, it should be not MTE
specific. The other processing which takes long time in the loop may
trigger soft lockup too.
So add cond_resched() for hugetlb to avoid soft lockup. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Add NULL pointer checks in dc_stream cursor attribute functions
The function dc_stream_set_cursor_attributes() currently dereferences
the `stream` pointer and nested members `stream->ctx->dc->current_state`
without checking for NULL.
All callers of these functions, such as in
`dcn30_apply_idle_power_optimizations()` and
`amdgpu_dm_plane_handle_cursor_update()`, already perform NULL checks
before calling these functions.
Fixes below:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c:336 dc_stream_program_cursor_attributes()
error: we previously assumed 'stream' could be null (see line 334)
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
327 bool dc_stream_program_cursor_attributes(
328 struct dc_stream_state *stream,
329 const struct dc_cursor_attributes *attributes)
330 {
331 struct dc *dc;
332 bool reset_idle_optimizations = false;
333
334 dc = stream ? stream->ctx->dc : NULL;
^^^^^^
The old code assumed stream could be NULL.
335
--> 336 if (dc_stream_set_cursor_attributes(stream, attributes)) {
^^^^^^
The refactor added an unchecked dereference.
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_stream.c
313 bool dc_stream_set_cursor_attributes(
314 struct dc_stream_state *stream,
315 const struct dc_cursor_attributes *attributes)
316 {
317 bool result = false;
318
319 if (dc_stream_check_cursor_attributes(stream, stream->ctx->dc->current_state, attributes)) {
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ Here.
This function used to check for if stream as NULL and return false at
the start. Probably we should add that back. |
| In the Linux kernel, the following vulnerability has been resolved:
blk-throttle: fix access race during throttle policy activation
On repeated cold boots we occasionally hit a NULL pointer crash in
blk_should_throtl() when throttling is consulted before the throttle
policy is fully enabled for the queue. Checking only q->td != NULL is
insufficient during early initialization, so blkg_to_pd() for the
throttle policy can still return NULL and blkg_to_tg() becomes NULL,
which later gets dereferenced.
Unable to handle kernel NULL pointer dereference
at virtual address 0000000000000156
...
pc : submit_bio_noacct+0x14c/0x4c8
lr : submit_bio_noacct+0x48/0x4c8
sp : ffff800087f0b690
x29: ffff800087f0b690 x28: 0000000000005f90 x27: ffff00068af393c0
x26: 0000000000080000 x25: 000000000002fbc0 x24: ffff000684ddcc70
x23: 0000000000000000 x22: 0000000000000000 x21: 0000000000000000
x20: 0000000000080000 x19: ffff000684ddcd08 x18: ffffffffffffffff
x17: 0000000000000000 x16: ffff80008132a550 x15: 0000ffff98020fff
x14: 0000000000000000 x13: 1fffe000d11d7021 x12: ffff000688eb810c
x11: ffff00077ec4bb80 x10: ffff000688dcb720 x9 : ffff80008068ef60
x8 : 00000a6fb8a86e85 x7 : 000000000000111e x6 : 0000000000000002
x5 : 0000000000000246 x4 : 0000000000015cff x3 : 0000000000394500
x2 : ffff000682e35e40 x1 : 0000000000364940 x0 : 000000000000001a
Call trace:
submit_bio_noacct+0x14c/0x4c8
verity_map+0x178/0x2c8
__map_bio+0x228/0x250
dm_submit_bio+0x1c4/0x678
__submit_bio+0x170/0x230
submit_bio_noacct_nocheck+0x16c/0x388
submit_bio_noacct+0x16c/0x4c8
submit_bio+0xb4/0x210
f2fs_submit_read_bio+0x4c/0xf0
f2fs_mpage_readpages+0x3b0/0x5f0
f2fs_readahead+0x90/0xe8
Tighten blk_throtl_activated() to also require that the throttle policy
bit is set on the queue:
return q->td != NULL &&
test_bit(blkcg_policy_throtl.plid, q->blkcg_pols);
This prevents blk_should_throtl() from accessing throttle group state
until policy data has been attached to blkgs. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: dont report verifier bug for missing bpf_scc_visit on speculative path
Syzbot generated a program that triggers a verifier_bug() call in
maybe_exit_scc(). maybe_exit_scc() assumes that, when called for a
state with insn_idx in some SCC, there should be an instance of struct
bpf_scc_visit allocated for that SCC. Turns out the assumption does
not hold for speculative execution paths. See example in the next
patch.
maybe_scc_exit() is called from update_branch_counts() for states that
reach branch count of zero, meaning that path exploration for a
particular path is finished. Path exploration can finish in one of
three ways:
a. Verification error is found. In this case, update_branch_counts()
is called only for non-speculative paths.
b. Top level BPF_EXIT is reached. Such instructions are never a part of
an SCC, so compute_scc_callchain() in maybe_scc_exit() will return
false, and maybe_scc_exit() will return early.
c. A checkpoint is reached and matched. Checkpoints are created by
is_state_visited(), which calls maybe_enter_scc(), which allocates
bpf_scc_visit instances for checkpoints within SCCs.
Hence, for non-speculative symbolic execution paths, the assumption
still holds: if maybe_scc_exit() is called for a state within an SCC,
bpf_scc_visit instance must exist.
This patch removes the verifier_bug() call for speculative paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: pcm: Disable bottom softirqs as part of spin_lock_irq() on PREEMPT_RT
snd_pcm_group_lock_irq() acquires a spinlock_t and disables interrupts
via spin_lock_irq(). This also implicitly disables the handling of
softirqs such as TIMER_SOFTIRQ.
On PREEMPT_RT softirqs are preemptible and spin_lock_irq() does not
disable them. That means a timer can be invoked during spin_lock_irq()
on the same CPU. Due to synchronisations reasons local_bh_disable() has
a per-CPU lock named softirq_ctrl.lock which synchronizes individual
softirq against each other.
syz-bot managed to trigger a lockdep report where softirq_ctrl.lock is
acquired in hrtimer_cancel() in addition to hrtimer_run_softirq(). This
is a possible deadlock.
The softirq_ctrl.lock can not be made part of spin_lock_irq() as this
would lead to too much synchronisation against individual threads on the
system. To avoid the possible deadlock, softirqs must be manually
disabled before the lock is acquired.
Disable softirqs before the lock is acquired on PREEMPT_RT. |
