| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix DMA transfer direction
When CONFIG_DMA_API_DEBUG is selected, while running the crypto self
test on the QAT crypto algorithms, the function add_dma_entry() reports
a warning similar to the one below, saying that overlapping mappings
are not supported. This occurs in tests where the input and the output
scatter list point to the same buffers (i.e. two different scatter lists
which point to the same chunks of memory).
The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL
for both the input and the output scatter lists which leads to
overlapped write mappings. These are not supported by the DMA layer.
Fix by specifying the correct DMA transfer directions when mapping
buffers. For in-place operations where the input scatter list
matches the output scatter list, buffers are mapped once with
DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag
DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE.
Overlapping a read mapping with a write mapping is a valid case in
dma-coherent devices like QAT.
The function that frees and unmaps the buffers, qat_alg_free_bufl()
has been changed accordingly to the changes to the mapping function.
DMA-API: 4xxx 0000:06:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported
WARNING: CPU: 53 PID: 4362 at kernel/dma/debug.c:570 add_dma_entry+0x1e9/0x270
...
Call Trace:
dma_map_page_attrs+0x82/0x2d0
? preempt_count_add+0x6a/0xa0
qat_alg_sgl_to_bufl+0x45b/0x990 [intel_qat]
qat_alg_aead_dec+0x71/0x250 [intel_qat]
crypto_aead_decrypt+0x3d/0x70
test_aead_vec_cfg+0x649/0x810
? number+0x310/0x3a0
? vsnprintf+0x2a3/0x550
? scnprintf+0x42/0x70
? valid_sg_divisions.constprop.0+0x86/0xa0
? test_aead_vec+0xdf/0x120
test_aead_vec+0xdf/0x120
alg_test_aead+0x185/0x400
alg_test+0x3d8/0x500
? crypto_acomp_scomp_free_ctx+0x30/0x30
? __schedule+0x32a/0x12a0
? ttwu_queue_wakelist+0xbf/0x110
? _raw_spin_unlock_irqrestore+0x23/0x40
? try_to_wake_up+0x83/0x570
? _raw_spin_unlock_irqrestore+0x23/0x40
? __set_cpus_allowed_ptr_locked+0xea/0x1b0
? crypto_acomp_scomp_free_ctx+0x30/0x30
cryptomgr_test+0x27/0x50
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/stm: ltdc: fix late dereference check
In ltdc_crtc_set_crc_source(), struct drm_crtc was dereferenced in a
container_of() before the pointer check. This could cause a kernel panic.
Fix this smatch warning:
drivers/gpu/drm/stm/ltdc.c:1124 ltdc_crtc_set_crc_source() warn: variable dereferenced before check 'crtc' (see line 1119) |
| Insufficient control flow management in the Linux kernel-mode driver for some Intel(R) 800 Series Ethernet before version 1.17.2 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| NVIDIA Display Driver for Linux contains a vulnerability where an attacker might be able to use a race condition to escalate privileges. A successful exploit of this vulnerability might lead to code execution, escalation of privileges, data tampering, denial of service, and information disclosure. |
| Improper check for unusual or exceptional conditions in the Linux kernel-mode driver for some Intel(R) 800 Series Ethernet before version 1.17.2 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| Improper input validation in the Linux kernel-mode driver for some Intel(R) 700 Series Ethernet before version 2.28.5 may allow an authenticated user to potentially enable escalation of privilege via local access. |
| In the Linux kernel, the following vulnerability has been resolved:
mmc: toshsd: fix return value check of mmc_add_host()
mmc_add_host() may return error, if we ignore its return value, the memory
that allocated in mmc_alloc_host() will be leaked and it will lead a kernel
crash because of deleting not added device in the remove path.
So fix this by checking the return value and goto error path which will call
mmc_free_host(), besides, free_irq() also needs be called. |
| In the Linux kernel, the following vulnerability has been resolved:
of: overlay: fix null pointer dereferencing in find_dup_cset_node_entry() and find_dup_cset_prop()
When kmalloc() fail to allocate memory in kasprintf(), fn_1 or fn_2 will
be NULL, and strcmp() will cause null pointer dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
ARM: OMAP2+: Fix memory leak in realtime_counter_init()
The "sys_clk" resource is malloced by clk_get(),
it is not released when the function return. |
| In the Linux kernel, the following vulnerability has been resolved:
udmabuf: Set ubuf->sg = NULL if the creation of sg table fails
When userspace tries to map the dmabuf and if for some reason
(e.g. OOM) the creation of the sg table fails, ubuf->sg needs to be
set to NULL. Otherwise, when the userspace subsequently closes the
dmabuf fd, we'd try to erroneously free the invalid sg table from
release_udmabuf resulting in the following crash reported by syzbot:
general protection fault, probably for non-canonical address
0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 3609 Comm: syz-executor487 Not tainted
5.19.0-syzkaller-13930-g7ebfc85e2cd7 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 07/22/2022
RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline]
RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline]
RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114
Code: 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 2b 04 00 00 48 8d 7d 0c 4c
8b 63 30 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 14
02 48 89 f8 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 e2
RSP: 0018:ffffc900037efd30 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffffff8cb67800 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff84ad27e0 RDI: 0000000000000000
RBP: fffffffffffffff4 R08: 0000000000000005 R09: 0000000000000000
R10: 0000000000000000 R11: 000000000008c07c R12: ffff88801fa05000
R13: ffff888073db07e8 R14: ffff888025c25440 R15: 0000000000000000
FS: 0000555555fc4300(0000) GS:ffff8880b9a00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fc1c0ce06e4 CR3: 00000000715e6000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
dma_buf_release+0x157/0x2d0 drivers/dma-buf/dma-buf.c:78
__dentry_kill+0x42b/0x640 fs/dcache.c:612
dentry_kill fs/dcache.c:733 [inline]
dput+0x806/0xdb0 fs/dcache.c:913
__fput+0x39c/0x9d0 fs/file_table.c:333
task_work_run+0xdd/0x1a0 kernel/task_work.c:177
ptrace_notify+0x114/0x140 kernel/signal.c:2353
ptrace_report_syscall include/linux/ptrace.h:420 [inline]
ptrace_report_syscall_exit include/linux/ptrace.h:482 [inline]
syscall_exit_work kernel/entry/common.c:249 [inline]
syscall_exit_to_user_mode_prepare+0x129/0x280 kernel/entry/common.c:276
__syscall_exit_to_user_mode_work kernel/entry/common.c:281 [inline]
syscall_exit_to_user_mode+0x9/0x50 kernel/entry/common.c:294
do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fc1c0c35b6b
Code: 0f 05 48 3d 00 f0 ff ff 77 45 c3 0f 1f 40 00 48 83 ec 18 89 7c 24
0c e8 63 fc ff ff 8b 7c 24 0c 41 89 c0 b8 03 00 00 00 0f 05 <48> 3d 00
f0 ff ff 77 35 44 89 c7 89 44 24 0c e8 a1 fc ff ff 8b 44
RSP: 002b:00007ffd78a06090 EFLAGS: 00000293 ORIG_RAX: 0000000000000003
RAX: 0000000000000000 RBX: 0000000000000007 RCX: 00007fc1c0c35b6b
RDX: 0000000020000280 RSI: 0000000040086200 RDI: 0000000000000006
RBP: 0000000000000007 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000293 R12: 000000000000000c
R13: 0000000000000003 R14: 00007fc1c0cfe4a0 R15: 00007ffd78a06140
</TASK>
Modules linked in:
---[ end trace 0000000000000000 ]---
RIP: 0010:dma_unmap_sgtable include/linux/dma-mapping.h:378 [inline]
RIP: 0010:put_sg_table drivers/dma-buf/udmabuf.c:89 [inline]
RIP: 0010:release_udmabuf+0xcb/0x4f0 drivers/dma-buf/udmabuf.c:114 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Fix running_req for internal abort commands
Disabling the remote phy for a SATA disk causes a hang:
root@(none)$ more /sys/class/sas_phy/phy-0:0:8/target_port_protocols
sata
root@(none)$ echo 0 > sys/class/sas_phy/phy-0:0:8/enable
root@(none)$ [ 67.855950] sas: ex 500e004aaaaaaa1f phy08 change count has changed
[ 67.920585] sd 0:0:2:0: [sdc] Synchronizing SCSI cache
[ 67.925780] sd 0:0:2:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
[ 67.935094] sd 0:0:2:0: [sdc] Stopping disk
[ 67.939305] sd 0:0:2:0: [sdc] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
...
[ 123.998998] INFO: task kworker/u192:1:642 blocked for more than 30 seconds.
[ 124.005960] Not tainted 6.0.0-rc1-205202-gf26f8f761e83 #218
[ 124.012049] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 124.019872] task:kworker/u192:1 state:D stack:0 pid: 642 ppid: 2 flags:0x00000008
[ 124.028223] Workqueue: 0000:04:00.0_event_q sas_port_event_worker
[ 124.034319] Call trace:
[ 124.036758] __switch_to+0x128/0x278
[ 124.040333] __schedule+0x434/0xa58
[ 124.043820] schedule+0x94/0x138
[ 124.047045] schedule_timeout+0x2fc/0x368
[ 124.051052] wait_for_completion+0xdc/0x200
[ 124.055234] __flush_workqueue+0x1a8/0x708
[ 124.059328] sas_porte_broadcast_rcvd+0xa8/0xc0
[ 124.063858] sas_port_event_worker+0x60/0x98
[ 124.068126] process_one_work+0x3f8/0x660
[ 124.072134] worker_thread+0x70/0x700
[ 124.075793] kthread+0x1a4/0x1b8
[ 124.079014] ret_from_fork+0x10/0x20
The issue is that the per-device running_req read in
pm8001_dev_gone_notify() never goes to zero and we never make progress.
This is caused by missing accounting for running_req for when an internal
abort command completes.
In commit 2cbbf489778e ("scsi: pm8001: Use libsas internal abort support")
we started to send internal abort commands as a proper sas_task. In this
when we deliver a sas_task to HW the per-device running_req is incremented
in pm8001_queue_command(). However it is never decremented for internal
abort commnds, so decrement in pm8001_mpi_task_abort_resp(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: hsr: avoid possible NULL deref in skb_clone()
syzbot got a crash [1] in skb_clone(), caused by a bug
in hsr_get_untagged_frame().
When/if create_stripped_skb_hsr() returns NULL, we must
not attempt to call skb_clone().
While we are at it, replace a WARN_ONCE() by netdev_warn_once().
[1]
general protection fault, probably for non-canonical address 0xdffffc000000000f: 0000 [#1] PREEMPT SMP KASAN
KASAN: null-ptr-deref in range [0x0000000000000078-0x000000000000007f]
CPU: 1 PID: 754 Comm: syz-executor.0 Not tainted 6.0.0-syzkaller-02734-g0326074ff465 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/22/2022
RIP: 0010:skb_clone+0x108/0x3c0 net/core/skbuff.c:1641
Code: 93 02 00 00 49 83 7c 24 28 00 0f 85 e9 00 00 00 e8 5d 4a 29 fa 4c 8d 75 7e 48 b8 00 00 00 00 00 fc ff df 4c 89 f2 48 c1 ea 03 <0f> b6 04 02 4c 89 f2 83 e2 07 38 d0 7f 08 84 c0 0f 85 9e 01 00 00
RSP: 0018:ffffc90003ccf4e0 EFLAGS: 00010207
RAX: dffffc0000000000 RBX: ffffc90003ccf5f8 RCX: ffffc9000c24b000
RDX: 000000000000000f RSI: ffffffff8751cb13 RDI: 0000000000000000
RBP: 0000000000000000 R08: 00000000000000f0 R09: 0000000000000140
R10: fffffbfff181d972 R11: 0000000000000000 R12: ffff888161fc3640
R13: 0000000000000a20 R14: 000000000000007e R15: ffffffff8dc5f620
FS: 00007feb621e4700(0000) GS:ffff8880b9b00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007feb621e3ff8 CR3: 00000001643a9000 CR4: 00000000003506e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
hsr_get_untagged_frame+0x4e/0x610 net/hsr/hsr_forward.c:164
hsr_forward_do net/hsr/hsr_forward.c:461 [inline]
hsr_forward_skb+0xcca/0x1d50 net/hsr/hsr_forward.c:623
hsr_handle_frame+0x588/0x7c0 net/hsr/hsr_slave.c:69
__netif_receive_skb_core+0x9fe/0x38f0 net/core/dev.c:5379
__netif_receive_skb_one_core+0xae/0x180 net/core/dev.c:5483
__netif_receive_skb+0x1f/0x1c0 net/core/dev.c:5599
netif_receive_skb_internal net/core/dev.c:5685 [inline]
netif_receive_skb+0x12f/0x8d0 net/core/dev.c:5744
tun_rx_batched+0x4ab/0x7a0 drivers/net/tun.c:1544
tun_get_user+0x2686/0x3a00 drivers/net/tun.c:1995
tun_chr_write_iter+0xdb/0x200 drivers/net/tun.c:2025
call_write_iter include/linux/fs.h:2187 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9e9/0xdd0 fs/read_write.c:584
ksys_write+0x127/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd |
| In the Linux kernel, the following vulnerability has been resolved:
ext2: Add sanity checks for group and filesystem size
Add sanity check that filesystem size does not exceed the underlying
device size and that group size is big enough so that metadata can fit
into it. This avoid trying to mount some crafted filesystems with
extremely large group counts. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: hisilicon/zip - fix mismatch in get/set sgl_sge_nr
KASAN reported this Bug:
[17619.659757] BUG: KASAN: global-out-of-bounds in param_get_int+0x34/0x60
[17619.673193] Read of size 4 at addr fffff01332d7ed00 by task read_all/1507958
...
[17619.698934] The buggy address belongs to the variable:
[17619.708371] sgl_sge_nr+0x0/0xffffffffffffa300 [hisi_zip]
There is a mismatch in hisi_zip when get/set the variable sgl_sge_nr.
The type of sgl_sge_nr is u16, and get/set sgl_sge_nr by
param_get/set_int.
Replacing param_get/set_int to param_get/set_ushort can fix this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
drivers: mcb: fix resource leak in mcb_probe()
When probe hook function failed in mcb_probe(), it doesn't put the device.
Compiled test only. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: fix bug_on in __es_tree_search caused by bad quota inode
We got a issue as fllows:
==================================================================
kernel BUG at fs/ext4/extents_status.c:202!
invalid opcode: 0000 [#1] PREEMPT SMP
CPU: 1 PID: 810 Comm: mount Not tainted 6.1.0-rc1-next-g9631525255e3 #352
RIP: 0010:__es_tree_search.isra.0+0xb8/0xe0
RSP: 0018:ffffc90001227900 EFLAGS: 00010202
RAX: 0000000000000000 RBX: 0000000077512a0f RCX: 0000000000000000
RDX: 0000000000000002 RSI: 0000000000002a10 RDI: ffff8881004cd0c8
RBP: ffff888177512ac8 R08: 47ffffffffffffff R09: 0000000000000001
R10: 0000000000000001 R11: 00000000000679af R12: 0000000000002a10
R13: ffff888177512d88 R14: 0000000077512a10 R15: 0000000000000000
FS: 00007f4bd76dbc40(0000)GS:ffff88842fd00000(0000)knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005653bf993cf8 CR3: 000000017bfdf000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ext4_es_cache_extent+0xe2/0x210
ext4_cache_extents+0xd2/0x110
ext4_find_extent+0x5d5/0x8c0
ext4_ext_map_blocks+0x9c/0x1d30
ext4_map_blocks+0x431/0xa50
ext4_getblk+0x82/0x340
ext4_bread+0x14/0x110
ext4_quota_read+0xf0/0x180
v2_read_header+0x24/0x90
v2_check_quota_file+0x2f/0xa0
dquot_load_quota_sb+0x26c/0x760
dquot_load_quota_inode+0xa5/0x190
ext4_enable_quotas+0x14c/0x300
__ext4_fill_super+0x31cc/0x32c0
ext4_fill_super+0x115/0x2d0
get_tree_bdev+0x1d2/0x360
ext4_get_tree+0x19/0x30
vfs_get_tree+0x26/0xe0
path_mount+0x81d/0xfc0
do_mount+0x8d/0xc0
__x64_sys_mount+0xc0/0x160
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
==================================================================
Above issue may happen as follows:
-------------------------------------
ext4_fill_super
ext4_orphan_cleanup
ext4_enable_quotas
ext4_quota_enable
ext4_iget --> get error inode <5>
ext4_ext_check_inode --> Wrong imode makes it escape inspection
make_bad_inode(inode) --> EXT4_BOOT_LOADER_INO set imode
dquot_load_quota_inode
vfs_setup_quota_inode --> check pass
dquot_load_quota_sb
v2_check_quota_file
v2_read_header
ext4_quota_read
ext4_bread
ext4_getblk
ext4_map_blocks
ext4_ext_map_blocks
ext4_find_extent
ext4_cache_extents
ext4_es_cache_extent
__es_tree_search.isra.0
ext4_es_end --> Wrong extents trigger BUG_ON
In the above issue, s_usr_quota_inum is set to 5, but inode<5> contains
incorrect imode and disordered extents. Because 5 is EXT4_BOOT_LOADER_INO,
the ext4_ext_check_inode check in the ext4_iget function can be bypassed,
finally, the extents that are not checked trigger the BUG_ON in the
__es_tree_search function. To solve this issue, check whether the inode is
bad_inode in vfs_setup_quota_inode(). |
| In the Linux kernel, the following vulnerability has been resolved:
amdgpu/pm: prevent array underflow in vega20_odn_edit_dpm_table()
In the PP_OD_EDIT_VDDC_CURVE case the "input_index" variable is capped at
2 but not checked for negative values so it results in an out of bounds
read. This value comes from the user via sysfs. |
| In the Linux kernel, the following vulnerability has been resolved:
mptcp: use proper req destructor for IPv6
Before, only the destructor from TCP request sock in IPv4 was called
even if the subflow was IPv6.
It is important to use the right destructor to avoid memory leaks with
some advanced IPv6 features, e.g. when the request socks contain
specific IPv6 options. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: smartpqi: Correct device removal for multi-actuator devices
Correct device count for multi-actuator drives which can cause kernel
panics. |
| In the Linux kernel, the following vulnerability has been resolved:
fbdev: smscufx: Fix several use-after-free bugs
Several types of UAFs can occur when physically removing a USB device.
Adds ufx_ops_destroy() function to .fb_destroy of fb_ops, and
in this function, there is kref_put() that finally calls ufx_free().
This fix prevents multiple UAFs. |
