| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
HSI: ssi_protocol: fix potential resource leak in ssip_pn_open()
ssip_pn_open() claims the HSI client's port with hsi_claim_port(). When
hsi_register_port_event() gets some error and returns a negetive value,
the HSI client's port should be released with hsi_release_port().
Fix it by calling hsi_release_port() when hsi_register_port_event() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: avoid uninit memory read in ath9k_htc_rx_msg()
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol. |
| In the Linux kernel, the following vulnerability has been resolved:
devlink: hold region lock when flushing snapshots
Netdevsim triggers a splat on reload, when it destroys regions
with snapshots pending:
WARNING: CPU: 1 PID: 787 at net/core/devlink.c:6291 devlink_region_snapshot_del+0x12e/0x140
CPU: 1 PID: 787 Comm: devlink Not tainted 6.1.0-07460-g7ae9888d6e1c #580
RIP: 0010:devlink_region_snapshot_del+0x12e/0x140
Call Trace:
<TASK>
devl_region_destroy+0x70/0x140
nsim_dev_reload_down+0x2f/0x60 [netdevsim]
devlink_reload+0x1f7/0x360
devlink_nl_cmd_reload+0x6ce/0x860
genl_family_rcv_msg_doit.isra.0+0x145/0x1c0
This is the locking assert in devlink_region_snapshot_del(),
we're supposed to be holding the region->snapshot_lock here. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7921e: fix rmmod crash in driver reload test
In insmod/rmmod stress test, the following crash dump shows up immediately.
The problem is caused by missing mt76_dev in mt7921_pci_remove(). We
should make sure the drvdata is ready before probe() finished.
[168.862789] ==================================================================
[168.862797] BUG: KASAN: user-memory-access in try_to_grab_pending+0x59/0x480
[168.862805] Write of size 8 at addr 0000000000006df0 by task rmmod/5361
[168.862812] CPU: 7 PID: 5361 Comm: rmmod Tainted: G OE 5.19.0-rc6 #1
[168.862816] Hardware name: Intel(R) Client Systems NUC8i7BEH/NUC8BEB, 05/04/2020
[168.862820] Call Trace:
[168.862822] <TASK>
[168.862825] dump_stack_lvl+0x49/0x63
[168.862832] print_report.cold+0x493/0x6b7
[168.862845] kasan_report+0xa7/0x120
[168.862857] kasan_check_range+0x163/0x200
[168.862861] __kasan_check_write+0x14/0x20
[168.862866] try_to_grab_pending+0x59/0x480
[168.862870] __cancel_work_timer+0xbb/0x340
[168.862898] cancel_work_sync+0x10/0x20
[168.862902] mt7921_pci_remove+0x61/0x1c0 [mt7921e]
[168.862909] pci_device_remove+0xa3/0x1d0
[168.862914] device_remove+0xc4/0x170
[168.862920] device_release_driver_internal+0x163/0x300
[168.862925] driver_detach+0xc7/0x1a0
[168.862930] bus_remove_driver+0xeb/0x2d0
[168.862935] driver_unregister+0x71/0xb0
[168.862939] pci_unregister_driver+0x30/0x230
[168.862944] mt7921_pci_driver_exit+0x10/0x1b [mt7921e]
[168.862949] __x64_sys_delete_module+0x2f9/0x4b0
[168.862968] do_syscall_64+0x38/0x90
[168.862973] entry_SYSCALL_64_after_hwframe+0x63/0xcd
Test steps:
1. insmode
2. do not ifup
3. rmmod quickly (within 1 second) |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: stop mdx_raid1 thread when raid1 array run failed
fail run raid1 array when we assemble array with the inactive disk only,
but the mdx_raid1 thread were not stop, Even if the associated resources
have been released. it will caused a NULL dereference when we do poweroff.
This causes the following Oops:
[ 287.587787] BUG: kernel NULL pointer dereference, address: 0000000000000070
[ 287.594762] #PF: supervisor read access in kernel mode
[ 287.599912] #PF: error_code(0x0000) - not-present page
[ 287.605061] PGD 0 P4D 0
[ 287.607612] Oops: 0000 [#1] SMP NOPTI
[ 287.611287] CPU: 3 PID: 5265 Comm: md0_raid1 Tainted: G U 5.10.146 #0
[ 287.619029] Hardware name: xxxxxxx/To be filled by O.E.M, BIOS 5.19 06/16/2022
[ 287.626775] RIP: 0010:md_check_recovery+0x57/0x500 [md_mod]
[ 287.632357] Code: fe 01 00 00 48 83 bb 10 03 00 00 00 74 08 48 89 ......
[ 287.651118] RSP: 0018:ffffc90000433d78 EFLAGS: 00010202
[ 287.656347] RAX: 0000000000000000 RBX: ffff888105986800 RCX: 0000000000000000
[ 287.663491] RDX: ffffc90000433bb0 RSI: 00000000ffffefff RDI: ffff888105986800
[ 287.670634] RBP: ffffc90000433da0 R08: 0000000000000000 R09: c0000000ffffefff
[ 287.677771] R10: 0000000000000001 R11: ffffc90000433ba8 R12: ffff888105986800
[ 287.684907] R13: 0000000000000000 R14: fffffffffffffe00 R15: ffff888100b6b500
[ 287.692052] FS: 0000000000000000(0000) GS:ffff888277f80000(0000) knlGS:0000000000000000
[ 287.700149] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 287.705897] CR2: 0000000000000070 CR3: 000000000320a000 CR4: 0000000000350ee0
[ 287.713033] Call Trace:
[ 287.715498] raid1d+0x6c/0xbbb [raid1]
[ 287.719256] ? __schedule+0x1ff/0x760
[ 287.722930] ? schedule+0x3b/0xb0
[ 287.726260] ? schedule_timeout+0x1ed/0x290
[ 287.730456] ? __switch_to+0x11f/0x400
[ 287.734219] md_thread+0xe9/0x140 [md_mod]
[ 287.738328] ? md_thread+0xe9/0x140 [md_mod]
[ 287.742601] ? wait_woken+0x80/0x80
[ 287.746097] ? md_register_thread+0xe0/0xe0 [md_mod]
[ 287.751064] kthread+0x11a/0x140
[ 287.754300] ? kthread_park+0x90/0x90
[ 287.757974] ret_from_fork+0x1f/0x30
In fact, when raid1 array run fail, we need to do
md_unregister_thread() before raid1_free(). |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix pci device refcount leak
As comment of pci_get_domain_bus_and_slot() says, it returns
a pci device with refcount increment, when finish using it,
the caller must decrement the reference count by calling
pci_dev_put().
So before returning from amdgpu_device_resume|suspend_display_audio(),
pci_dev_put() is called to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: qcom-adm: fix wrong calling convention for prep_slave_sg
The calling convention for pre_slave_sg is to return NULL on error and
provide an error log to the system. Qcom-adm instead provide error
pointer when an error occur. This indirectly cause kernel panic for
example for the nandc driver that checks only if the pointer returned by
device_prep_slave_sg is not NULL. Returning an error pointer makes nandc
think the device_prep_slave_sg function correctly completed and makes
the kernel panics later in the code.
While nandc is the one that makes the kernel crash, it was pointed out
that the real problem is qcom-adm not following calling convention for
that function.
To fix this, drop returning error pointer and return NULL with an error
log. |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: fix resource leak in regulator_register()
I got some resource leak reports while doing fault injection test:
OF: ERROR: memory leak, expected refcount 1 instead of 100,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /i2c/pmic@64/regulators/buck1
unreferenced object 0xffff88810deea000 (size 512):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859840 (age 5061.046s)
hex dump (first 32 bytes):
00 00 00 00 ad 4e ad de ff ff ff ff 00 00 00 00 .....N..........
ff ff ff ff ff ff ff ff a0 1e 00 a1 ff ff ff ff ................
backtrace:
[<00000000d78541e2>] kmalloc_trace+0x21/0x110
[<00000000b343d153>] device_private_init+0x32/0xd0
[<00000000be1f0c70>] device_add+0xb2d/0x1030
[<00000000e3e6344d>] regulator_register+0xaf2/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
unreferenced object 0xffff88810b617b80 (size 32):
comm "490-i2c-rt5190a", pid 253, jiffies 4294859904 (age 5060.983s)
hex dump (first 32 bytes):
72 65 67 75 6c 61 74 6f 72 2e 32 38 36 38 2d 53 regulator.2868-S
55 50 50 4c 59 00 ff ff 29 00 00 00 2b 00 00 00 UPPLY...)...+...
backtrace:
[<000000009da9280d>] __kmalloc_node_track_caller+0x44/0x1b0
[<0000000025c6a4e5>] kstrdup+0x3a/0x70
[<00000000790efb69>] create_regulator+0xc0/0x4e0
[<0000000005ed203a>] regulator_resolve_supply+0x2d4/0x440
[<0000000045796214>] regulator_register+0x10b3/0x12a0
[<00000000e2f5e754>] devm_regulator_register+0x57/0xb0
[<000000008b898197>] rt5190a_probe+0x52a/0x861 [rt5190a_regulator]
After calling regulator_resolve_supply(), the 'rdev->supply' is set
by set_supply(), after this set, in the error path, the resources
need be released, so call regulator_put() to avoid the leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
media: vidtv: Fix use-after-free in vidtv_bridge_dvb_init()
KASAN reports a use-after-free:
BUG: KASAN: use-after-free in dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
Call Trace:
...
dvb_dmxdev_release+0x4d5/0x5d0 [dvb_core]
vidtv_bridge_probe+0x7bf/0xa40 [dvb_vidtv_bridge]
platform_probe+0xb6/0x170
...
Allocated by task 1238:
...
dvb_register_device+0x1a7/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
Freed by task 1238:
dvb_register_device+0x6d2/0xa70 [dvb_core]
dvb_dmxdev_init+0x2af/0x4a0 [dvb_core]
vidtv_bridge_probe+0x766/0xa40 [dvb_vidtv_bridge]
...
It is because the error handling in vidtv_bridge_dvb_init() is wrong.
First, vidtv_bridge_dmx(dev)_init() will clean themselves when fail, but
goto fail_dmx(_dev): calls release functions again, which causes
use-after-free.
Also, in fail_fe, fail_tuner_probe and fail_demod_probe, j = i will cause
out-of-bound when i finished its loop (i == NUM_FE). And the loop
releasing is wrong, although now NUM_FE is 1 so it won't cause problem.
Fix this by correctly releasing everything. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/lcs: Fix return type of lcs_start_xmit()
With clang's kernel control flow integrity (kCFI, CONFIG_CFI_CLANG),
indirect call targets are validated against the expected function
pointer prototype to make sure the call target is valid to help mitigate
ROP attacks. If they are not identical, there is a failure at run time,
which manifests as either a kernel panic or thread getting killed. A
proposed warning in clang aims to catch these at compile time, which
reveals:
drivers/s390/net/lcs.c:2090:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
drivers/s390/net/lcs.c:2097:21: error: incompatible function pointer types initializing 'netdev_tx_t (*)(struct sk_buff *, struct net_device *)' (aka 'enum netdev_tx (*)(struct sk_buff *, struct net_device *)') with an expression of type 'int (struct sk_buff *, struct net_device *)' [-Werror,-Wincompatible-function-pointer-types-strict]
.ndo_start_xmit = lcs_start_xmit,
^~~~~~~~~~~~~~
->ndo_start_xmit() in 'struct net_device_ops' expects a return type of
'netdev_tx_t', not 'int'. Adjust the return type of lcs_start_xmit() to
match the prototype's to resolve the warning and potential CFI failure,
should s390 select ARCH_SUPPORTS_CFI_CLANG in the future. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: Fix resource leak in ksmbd_session_rpc_open()
When ksmbd_rpc_open() fails then it must call ksmbd_rpc_id_free() to
undo the result of ksmbd_ipc_id_alloc(). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: silence the warning when evicting inode with dioread_nolock
When evicting an inode with default dioread_nolock, it could be raced by
the unwritten extents converting kworker after writeback some new
allocated dirty blocks. It convert unwritten extents to written, the
extents could be merged to upper level and free extent blocks, so it
could mark the inode dirty again even this inode has been marked
I_FREEING. But the inode->i_io_list check and warning in
ext4_evict_inode() missing this corner case. Fortunately,
ext4_evict_inode() will wait all extents converting finished before this
check, so it will not lead to inode use-after-free problem, every thing
is OK besides this warning. The WARN_ON_ONCE was originally designed
for finding inode use-after-free issues in advance, but if we add
current dioread_nolock case in, it will become not quite useful, so fix
this warning by just remove this check.
======
WARNING: CPU: 7 PID: 1092 at fs/ext4/inode.c:227
ext4_evict_inode+0x875/0xc60
...
RIP: 0010:ext4_evict_inode+0x875/0xc60
...
Call Trace:
<TASK>
evict+0x11c/0x2b0
iput+0x236/0x3a0
do_unlinkat+0x1b4/0x490
__x64_sys_unlinkat+0x4c/0xb0
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x46/0xb0
RIP: 0033:0x7fa933c1115b
======
rm kworker
ext4_end_io_end()
vfs_unlink()
ext4_unlink()
ext4_convert_unwritten_io_end_vec()
ext4_convert_unwritten_extents()
ext4_map_blocks()
ext4_ext_map_blocks()
ext4_ext_try_to_merge_up()
__mark_inode_dirty()
check !I_FREEING
locked_inode_to_wb_and_lock_list()
iput()
iput_final()
evict()
ext4_evict_inode()
truncate_inode_pages_final() //wait release io_end
inode_io_list_move_locked()
ext4_release_io_end()
trigger WARN_ON_ONCE() |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: akcipher - default implementation for setting a private key
Changes from v1:
* removed the default implementation from set_pub_key: it is assumed that
an implementation must always have this callback defined as there are
no use case for an algorithm, which doesn't need a public key
Many akcipher implementations (like ECDSA) support only signature
verifications, so they don't have all callbacks defined.
Commit 78a0324f4a53 ("crypto: akcipher - default implementations for
request callbacks") introduced default callbacks for sign/verify
operations, which just return an error code.
However, these are not enough, because before calling sign the caller would
likely call set_priv_key first on the instantiated transform (as the
in-kernel testmgr does). This function does not have a default stub, so the
kernel crashes, when trying to set a private key on an akcipher, which
doesn't support signature generation.
I've noticed this, when trying to add a KAT vector for ECDSA signature to
the testmgr.
With this patch the testmgr returns an error in dmesg (as it should)
instead of crashing the kernel NULL ptr dereference. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: idmouse: fix an uninit-value in idmouse_open
In idmouse_create_image, if any ftip_command fails, it will
go to the reset label. However, this leads to the data in
bulk_in_buffer[HEADER..IMGSIZE] uninitialized. And the check
for valid image incurs an uninitialized dereference.
Fix this by moving the check before reset label since this
check only be valid if the data after bulk_in_buffer[HEADER]
has concrete data.
Note that this is found by KMSAN, so only kernel compilation
is tested. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmem: core: Fix memleak in nvmem_register()
dev_set_name will alloc memory for nvmem->dev.kobj.name in
nvmem_register, when nvmem_validate_keepouts failed, nvmem's
memory will be freed and return, but nobody will free memory
for nvmem->dev.kobj.name, there will be memleak, so moving
nvmem_validate_keepouts() after device_register() and let
the device core deal with cleaning name in error cases. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: do not run mt76u_status_worker if the device is not running
Fix the following NULL pointer dereference avoiding to run
mt76u_status_worker thread if the device is not running yet.
KASAN: null-ptr-deref in range
[0x0000000000000000-0x0000000000000007]
CPU: 0 PID: 98 Comm: kworker/u2:2 Not tainted 5.14.0+ #78 Hardware
name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: mt76 mt76u_tx_status_data
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Call Trace:
mt76x02_send_tx_status+0x1d2/0xeb0
mt76x02_tx_status_data+0x8e/0xd0
mt76u_tx_status_data+0xe1/0x240
process_one_work+0x92b/0x1460
worker_thread+0x95/0xe00
kthread+0x3a1/0x480
ret_from_fork+0x1f/0x30
Modules linked in:
--[ end trace 8df5d20fc5040f65 ]--
RIP: 0010:mt76x02_mac_fill_tx_status.isra.0+0x82c/0x9e0
Code: c5 48 b8 00 00 00 00 00 fc ff df 80 3c 02 00 0f 85 94 01 00 00
48 b8 00 00 00 00 00 fc ff df 4d 8b 34 24 4c 89 f2 48 c1 ea 03 <0f>
b6
04 02 84 c0 74 08 3c 03 0f 8e 89 01 00 00 41 8b 16 41 0f b7
RSP: 0018:ffffc900005af988 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffffc900005afae8 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff832fc661 RDI: ffffc900005afc2a
RBP: ffffc900005afae0 R08: 0000000000000001 R09: fffff520000b5f3c
R10: 0000000000000003 R11: fffff520000b5f3b R12: ffff88810b6132d8
R13: 000000000000ffff R14: 0000000000000000 R15: ffffc900005afc28
FS: 0000000000000000(0000) GS:ffff88811aa00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa0eda6a000 CR3: 0000000118f17000 CR4: 0000000000750ef0
PKRU: 55555554
Moreover move stat_work schedule out of the for loop. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: hif_usb: fix memory leak of urbs in ath9k_hif_usb_dealloc_tx_urbs()
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
media: imx-jpeg: Disable useless interrupt to avoid kernel panic
There is a hardware bug that the interrupt STMBUF_HALF may be triggered
after or when disable interrupt.
It may led to unexpected kernel panic.
And interrupt STMBUF_HALF and STMBUF_RTND have no other effect.
So disable them and the unused interrupts.
meanwhile clear the interrupt status when disable interrupt. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: Avoid UBSAN error on true_sectors_per_clst()
syzbot reported UBSAN error as below:
[ 76.901829][ T6677] ================================================================================
[ 76.903908][ T6677] UBSAN: shift-out-of-bounds in fs/ntfs3/super.c:675:13
[ 76.905363][ T6677] shift exponent -247 is negative
This patch avoid this error. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: marvell/octeontx - prevent integer overflows
The "code_length" value comes from the firmware file. If your firmware
is untrusted realistically there is probably very little you can do to
protect yourself. Still we try to limit the damage as much as possible.
Also Smatch marks any data read from the filesystem as untrusted and
prints warnings if it not capped correctly.
The "code_length * 2" can overflow. The round_up(ucode_size, 16) +
sizeof() expression can overflow too. Prevent these overflows. |
