| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
ata: ahci: fail probe if BAR too small for claimed ports
When an AHCI controller is disabled in BIOS, its HOST_CAP register may
contain a bogus value, e.g. 0xFFFFFFFF.
Since CAP.NP (Number of Ports) is a zeroes based 5-bit register field,
a value of 0x1f means 32 ports. If CAP.NP claims more ports than can
physically fit within the mapped BAR region, accessing port registers
beyond the BAR boundary causes a kernel panic.
Add validation in ahci_init_one() to check that the BAR size is
sufficient for the number of ports claimed in CAP.NP. The check
calculates the required MMIO size as:
required_size = 0x100 (global registers) + max_ports * 0x80
If required_size exceeds the actual BAR size, the probe fails with
-ENODEV, preventing the panic and providing a clear error message.
[cassel: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
net: qrtr: fix node refcount leak on ctrl packet alloc failure
qrtr_send_resume_tx() calls qrtr_node_lookup() which takes a
reference on the returned node. If the subsequent call to
qrtr_alloc_ctrl_packet() fails due to memory allocation failure, the
function returns -ENOMEM without calling qrtr_node_release() to
release the node reference.
Add qrtr_node_release(node) before returning on the allocation failure
path to properly release the reference. |
| In the Linux kernel, the following vulnerability has been resolved:
fs/ntfs3: preserve non-DOS attribute bits in system.dos_attrib
[BUG]
A corrupted ntfs3 image can hit a NULL function pointer call in
generic_perform_write() after toggling system.ntfs_attrib and then
overwriting system.dos_attrib on the same file.
BUG: kernel NULL pointer dereference, address: 0000000000000000
\#PF: supervisor instruction fetch in kernel mode
\#PF: error_code(0x0010) - not-present page
PGD bed5067 P4D bed5067 PUD 0
Oops: Oops: 0010 [#1] SMP KASAN NOPTI
RIP: 0010:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 0018:ffff88801025f988 EFLAGS: 00010246
Call Trace:
generic_perform_write+0x409/0x8c0 mm/filemap.c:4255
__generic_file_write_iter+0x1bb/0x200 mm/filemap.c:4372
ntfs_file_write_iter+0xcd9/0x1c20 fs/ntfs3/file.c:1253
new_sync_write fs/read_write.c:593 [inline]
vfs_write+0x63b/0xf70 fs/read_write.c:686
ksys_write+0x133/0x250 fs/read_write.c:738
__do_sys_write fs/read_write.c:749 [inline]
__se_sys_write fs/read_write.c:746 [inline]
__x64_sys_write+0x77/0xc0 fs/read_write.c:746
...
[CAUSE]
system.ntfs_attrib updates ATTR_DATA flags via ni_new_attr_flags()
and switches i_mapping->a_ops to ntfs_aops_cmpr when
FILE_ATTRIBUTE_COMPRESSED is set. system.dos_attrib then overwrites
ni->std_fa from a one-byte DOS attribute value, clearing the compression
bit without updating ATTR_DATA or the mapping operations.
Old buffered writes use is_compressed(ni) to choose
__generic_file_write_iter(). That leaves generic_perform_write() calling
a NULL write_begin callback from ntfs_aops_cmpr.
[FIX]
Treat system.dos_attrib as a low-byte DOS attribute update and preserve the
existing non-DOS attribute bits in ni->std_fa. This keeps compressed and
sparse state consistent with ATTR_DATA and the mapping operations while
keeping the existing DOS attribute semantics intact. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: rework FDB management on the bridge leave path
On bridge leave, the dpaa2_switch_port_set_fdb() function always
allocates a new FDB for the port which is becoming standalone. In case
no FDB is found, then the port leaving a bridge will continue to use the
current one.
The above logic does not cover the case in which there are multiple
bridges which have ports from the same DPSW instance. In this case, when
the last port leaves bridge #1, it finds an unused FDB to switch to, but
the old FDB is not marked as unused. Since the number of FDBs is equal
to the number of DPSW interfaces, this will eventually lead to multiple
ports sharing the same FDB.
Fix this by changing how we are managing the FDBs on the leave path.
Instead of directly allocating a new FDB, first verify if the current
port is the last one to leave a bridge. If this is the case, then
continue to use the current FDB and only allocate another FDB if there
are other ports remaining in the bridge. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: sja1105: flower: reject cross-chip redirect
dsa_port_from_netdev() may return a valid port from a different switch
chip. Programming another chip's port index into the local hardware
causes redirection to the wrong port, or an out-of-bounds access if the
index exceeds the local chip's port count.
Apply a minimal fix that adds a check to catch this case and adjusts the
extack message. When cls->common.skip_sw is not set, the operation could
instead redirect to the upstream port and let the software or upstream
switch(es) handle the forward, but that is not addressed here. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-switch: fix handling of NAPI on the remove path
All the NAPI instances for a DPSW device are attached to the first
switch port's net_device but shared by all ports. The NAPI instances get
disabled only once the last port goes down.
This causes an issue on the .remove() path where each port is
unregistered and freed one at a time, causing the NAPI instances to be
deleted even though they are not disabled.
In order to avoid this, split up the unregister_netdev() calls from the
free_netdev() so that we make sure all ports go down before we attempt
a deletion of NAPI instances. Also, make the netif_napi_del() explicit
as it is on the .probe() path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: fix P2P-Device binding handling
Our binding handling for P2P-Device can run into the following
scenario, as observed by our testing:
- a station interface is connected on some channel
- the P2P-Device does a remain-on-channel (ROC) on that channel
- the ROC ends, and the P2P-Device is removed from the binding,
but the phy_ctxt pointer is left around as a PHY cache so we
don't need to recalibrate to the channel again and again in
case it's not shared
- a binding update by the station interface, even a removal,
will re-add the P2P-Device to the binding
- the P2P-Device is removed, which removes the PHY context, but
it's still in the binding so the firmware crashes
Since the P2P device is removed from the binding and only re-
added by unrelated code, but we want to keep the phy_ctxt around
as a cache for future ROC usage, fix it by adding a boolean that
indicates whether or not the P2P-Device should be added to the
binding, and handle that in the binding iterator. That way, the
station interface cannot re-add the P2P-Device to the binding
when that isn't active. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Avoid DPMS-on for phantom stream
[Why & How]
Calling dc_update_planes_and_stream separately for stream and its
phantom stream causes a NULL pointer dereference, since the phantom is
destroyed on the first call.
Skip the call for phantom streams. |
| In the Linux kernel, the following vulnerability has been resolved:
xhci: Prevent queuing new commands if xhci is inaccessible
Refuse to queue a new command on the command ring if xHC is marked
inaccessible with the HCD_FLAG_HW_ACCESSIBLE.
HCD_FLAG_HW_ACCESSIBLE is set and cleared in suspend and resume.
Also print a warning if xhci is being suspended with commands
still pending on the command ring. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix UAF race in destroy_queue_cpsch
wait_on_destroy_queue() drops locks to wait for queue resume, allowing
a concurrent destroy to free the queue. Use is_being_destroyed flag to
serialize destruction. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/pm: bound pp_dpm_set_pp_table() memcpy
The powerplay path allocates hardcode_pp_table once with kmemdup(...,
soft_pp_table_size). memcpy(..., size) used the sysfs store count (up to
PAGE_SIZE) with no upper bound, causing heap overflow. Reject
writes where size exceeds soft_pp_table_size. |
| ESF-IDF is the Espressif Internet of Things (IOT) Development Framework. In 5.5.5, 6.0.1, and 6.1, the BlueDroid A2DP sink function btc_a2dp_sink_handle_inc_media() reads a timestamp field from the received media buffer before validating that the packet layout contains the field. A paired BR/EDR audio source within radio range can send a malformed A2DP media packet to a build with BlueDroid Classic Bluetooth and A2DP sink support enabled, causing an out-of-bounds read into adjacent heap memory and limited disclosure of heap contents. Arbitrary memory disclosure and code execution are not established. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/pm: fix SmartShift bias sysfs store PM refcount on parse error
Return the parse error before acquiring PM access. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: fix buffer overflow during vBIOS update
Clamp the buffer postion to write by setting the bin attribute
to the maximum buffer size so that VFS layer will block the
out-of-bounds accessing. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu/ras: add ras_suspend callback and use it for cp_ecc_error_irq
cp_ecc_error_irq is acquired in amdgpu_gfx_ras_late_init() but
released in gfx_v9_0_hw_fini(), so the put site has to query
amdgpu_irq_enabled() because the get is skipped on SR-IOV VF.
ras_late_init / ras_fini have no suspend counterpart, so move the
put to amdgpu_gfx_ras_suspend() / amdgpu_gfx_ras_fini() and add a
matching ras_suspend callback that is invoked from
amdgpu_ras_suspend() before disable_all_features(). The get and
put now sit in the same place and check the same condition (not
VF, funcs registered), no refcount querying needed.
An active flag gates ras_fini so the
suspend-then-unload-without-resume path falls into
amdgpu_ras_block_late_fini_default() instead of double-releasing
what ras_suspend already cleaned up.
Drop the cp_ecc_error_irq put from gfx_v9_0_hw_fini(). gfx_v8_0
manages cp_ecc_error_irq locally and is unaffected; no other GFX
generation has this IRQ. |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/region: Validate partition index before array access
construct_region() reads cxled->part and uses it to index
cxlds->part[] without checking for a negative value. If the
partition was never resolved, part remains at its initial value
of -1, causing an out-of-bounds array access.
Add a guard to return -EBUSY when part is negative.
The check was dropped during a merge. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix SMI event cross-process information leak
kfd_smi_ev_enabled() skips the suser privilege check when pid=0.
PROCESS_START, PROCESS_END, and VMFAULT events are emitted with
pid=0 while carrying another process's PID and command name, so any
/dev/kfd user in the render group can monitor all GPU workloads.
Pass the target process PID into kfd_smi_event_add() for these events
so the existing per-client filter restricts delivery to the owning
process or CAP_SYS_ADMIN subscribers. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/umem: Be careful about boundary conditions in ib_umem_find_best_pgsz()
Several corner cases, especially important on 32 bits:
- umem->iova is u64, the function argument should pass in u64 or
iova will be truncated
- Check that the length is not too large for the iova
- Check that lengths > 4G don't overflow the GENMASK |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: NUL-terminate replaced sysctl value
When writing to sysctls, proc_sys_call_handler() guarantees that the
buffer passed to proc handlers is NUL-terminated. If
bpf_sysctl_set_new_value() replaces the pending sysctl value, it can
hand a replacement buffer directly to proc handlers. However, the
helper currently copies only buf_len bytes into that buffer without
appending a NUL terminator, leaving downstream parsers vulnerable to
out-of-bounds access.
Fix this by appending a '\0' after the replaced value to restore the
expected sysctl semantics. Since the helper already rejects buf_len
greater than PAGE_SIZE - 1, there is always room for the extra byte.
Reproduced in a QEMU x86_64 guest booted with KASAN while exercising
the sysctl replacement path with a cgroup/sysctl BPF program. The
reproducer targets `/proc/sys/net/core/flow_limit_cpu_bitmap`, fills
the original user write buffer with non-zero bytes, and overrides the
sysctl value so the replacement buffer lacks a terminating NUL. Under
that setup, the pre-fix kernel reported:
BUG: KASAN: slab-out-of-bounds in strnchrnul+0x72/0x90
Read of size 1 at addr ffff88800de57000 by task repro_patch3/66
CPU: 0 UID: 0 PID: 66 Comm: repro_patch3 Not tainted 7.1.0-rc3-00269-g8370ca1f87cc #6 PREEMPT(lazy)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xa0
print_report+0xcb/0x5e0
? __virt_addr_valid+0x21d/0x3f0
? strnchrnul+0x72/0x90
? strnchrnul+0x72/0x90
kasan_report+0xca/0x100
? strnchrnul+0x72/0x90
strnchrnul+0x72/0x90
bitmap_parse+0x37/0x2e0
flow_limit_cpu_sysctl+0xc6/0x840
? __pfx_flow_limit_cpu_sysctl+0x10/0x10
? __kvmalloc_node_noprof+0x5ba/0x870
proc_sys_call_handler+0x31d/0x480
? __pfx_proc_sys_call_handler+0x10/0x10
? selinux_file_permission+0x39f/0x500
? lock_is_held_type+0x9e/0x120
vfs_write+0x98e/0x1000
...
</TASK>
The buggy address is located 0 bytes to the right of
allocated 4096-byte region [ffff88800de56000, ffff88800de57000)
With this fix applied, rerunning the same sysctl-targeted path yields
no corresponding KASAN reports. |
| In the Linux kernel, the following vulnerability has been resolved:
hsr: broadcast netlink notifications in the device's net namespace
The HSR generic netlink family sets .netnsok = true. HSR devices can
live in network namespaces other than init_net.
Two async notifiers broadcast events with genlmsg_multicast(). They
are hsr_nl_ringerror() and hsr_nl_nodedown(). That helper delivers
only on the default genl socket in init_net. So the events always land
in init_net. The network namespace of the device does not matter.
This has two effects. A listener in the device's own namespace never
sees its own ring error and node down events. A privileged listener in
init_net receives events from HSR devices in other namespaces. The
payload carries the peer node MAC (HSR_A_NODE_ADDR) and the slave port
ifindex (HSR_A_IFINDEX).
Switch both callers to genlmsg_multicast_netns(). Other families with
.netnsok = true already do this. Examples are gtp, ovpn, team,
batman-adv, netdev-genl, ethtool and handshake.
hsr_nl_ringerror() already has the slave port. It uses
dev_net(port->dev). hsr_nl_nodedown() takes the namespace from the
master port via hsr_port_get_hsr(). |
